rmrc recruit 3d models

Adjust the Infill Settings to Reach Optimal Weight Requirements for the RMRC Recruit V2 Wing.

nose weight for the RMRC recruit v2 wing adjust infill to achieve desired weight

I needed a new battery tray for my RMRC Recruit after accidentally breaking the original one.

I installed a new nose on my RMRC Recruit model, utilizing a 0.25mm layer height and minimal infill settings of 0%. ...The replacement part weighs approximately 32 grams.

If you've managed to crash your RMRC Recruit, replacing the winglets is likely in order. Instead of buying a partial wing replacement, simply print mine and save yourself some cash. This winglet boasts a sleeker design, with less of a tip on top for...

Others might also require an antenna mount for their Recruit. Therefore, I designed one myself and decided to share the idea with the community. ...The printout is made of TPU material, and its flexible nature provides a bit of bounce that effectively...

RMRC Recruit / AR Wing Battery Carrier Tray. ...A superior alternative to the standard wooden version.

RMRC Recruit / AR Wing Battery Tray. ... Stronger/better than original wooden one.

I modified the RMRC Recruit VTX/FC/GPS mount, scaling down the central segment to 24x24 in order to accommodate the Matek F411 Wing FC.

This is a mount similar to the wooden kit that comes with the RMRC Recruit to mount a Caddx Orca. The Strap holes are sized appropriately to fit the straps included with the Recruit. ...

This quick design is intended for an RMRC Recruit, accommodating a Matek VTX-HV module alongside virtually any 30.5x30.5 Flight Control board and a compact GPS unit. To avoid obstruction of the USB port, it's suggested that standoffs be used to...

This is a custom mount for the RMRC Recruit, designed specifically to accommodate an Insta360 One where a GoPro would typically fit. To make it work, you'll need to modify both the lid and the front cowling of the mount. Additionally, reinforce the...

This is a quick design for a RMRC Recruit. It holds a Matek VTX-HV, just about any 30.5x30.5 FC, and a micro GPS unit. The FC and VTX are on the same level so the usb plug is blocked. You may want to use some standoffs to raise the FC so the usb port...

A completely identical replica of the original model, minus its wooden frame.

Motor Mount and LED Holder for the Sonicmodel 900 Wing - a Custom Creation Combining the Best Features of Two Popular Designs. ...This innovative mashup brings together the reliability of mycopter's AR Wing 900 Motor Mount and the versatility of dre77's...

Print out your favorite image on whatever medium suits you best and proudly display that Pixfalcon mascot!

Motor Mount & Led Holder for the Sonicmodel 900 Wing. This thing is my Mashup of mycopter's AR Wing 900 Motor Mount & dre77's LED Halter fur AR Wing. ...Works with motors with 16x16mm mounting.

The slot at the back of the mount passes through the stock Recruit battery strap, providing additional security and stability. To prepare my Recruit for the new mount, I will need to modify the nose cone by making some precise cuts. ...I plan to print...

This adapter securely holds your FRSky X8R Antenna in place on your Recruit v2. ...Better reception is guaranteed when at least one antenna is vertical.\r\n\r\nUse mini zip ties through its holes for added stability, and highly recommend applying...

This holds your FRSky L9R Antenna in place on your Recruit v2 Drone. Vertical orientation is key for better reception, so consider mounting at least one antenna vertically. The design features holes for mini zip ties, which are a great way to secure...

Order pre-made in resin from my site: https://www.matter-replicator.com/product/ar900-rmrc-recruit-dji-fpv-air-unit-mount/

Order pre-made in resin from my site: https://www.matter-replicator.com/product/ar900-rmrc-recruit-dji-fpv-air-unit-mount/ Category: R/C Vehicles

Mount the Caddx Turtle V2 on your RMRC Recruit or AR Wing in a snap. Simply place it in front of the HD camera area, securing it with 3M VHB tape - but you can also glue it if that's your preference. Next, use the Caddx screws to lock down the DVR...

... into the height). Inspired by excellent concept design by harkal. You can purchase this pre-made on a liquid-resin stereo lithography printer from my webstore: http://www.matter-replicator.com/product/ar900-rmrc-recruit-dji-fpv-air-unit-mount/

This is a simple compact combo tray designed specifically for the F-35 FC & GPS, Holybro ATLATL V2 and stock 30A esc in RMRC Recruit and AR Wing 900 models. It will also work with standard 30.5x30.5 boards. To ensure a secure fit, we recommend using...

... Inspired by excellent concept design by harkal. You can purchase this pre-made on a liquid-resin stereo lithography printer from my webstore: http://www.matter-replicator.com/product/ar900-rmrc-recruit-dji-fpv-air-unit-mount/ Category: R/C Vehicles

... was inspired by harkal's exceptional design ideas. You can purchase this pre-assembled mount on a liquid-resin stereolithography printer through my online store: http://www.matter-replicator.com/product/ar900-rmrc-recruit-dji-fpv-air-unit-mount/

... for motors like the Brotherhobby 1806. ...The adapter ensures precise alignment of the motor, thanks to countersunk screw heads that match the original holes perfectly. Simply reuse the wood screws provided with the Recruit Mini to secure it in place.

I tweaked the model to unlock new possibilities, transforming the space previously occupied by the VTX into a prime location for the Runcam Split 2 board. ...The VTX now securely fastened to the wing mount, creating an ideal platform for mounting my...

I remade CarterClysm888's mount using only a few tweaks, specifically altering it to accommodate the standard 16x19mm motor bolt layout.