rmrc nano skyhunter 3d models

I repurposed a Samsung 360 case to attach it securely to the top of my RMRC Valorem, and I'm loving the result!

This is a mount similar to the wooden kit that comes with the RMRC Recruit to mount a Caddx Orca. The Strap holes are sized appropriately to fit the straps included with the Recruit. ...

Our upgraded Robot for RMRC 2019 is fully operational and ready to perform at the highest level. ...Watch its capabilities in action on YouTube at https://youtu.be/dZ74LjmgJ48.

A sleek and compact tool holder designed specifically to store the 3-piece tool set included in the RMRC, exclusively available during the limited-time St. ...Patrick's Flash Sale.

The mount secures the AKK X1 or comparable VTX design, fitting snugly onto the RMRC Valorem 250 upper plate while maintaining full access to the display and button from above. ...Secure it in place with two sturdy M3 x 16 bolts.

This is a straightforward guide for the RMRC Goby 210 for the narrow deck. A small chamfer on the inside of the counter bore facilitates successful prints without supports. Important Note: Socket cap screws will appear more flush. ... Print Settings...

Here is a design for mimicking the RMRC Cricket vTx mounting tabs. This solution is ideal for models such as the Strix Alatus, which features direct mounting for cricket vTx's. ...It can be scaled in any axis to fit virtually any vTx.

I just got my new Sonicmodell Skyhunter Nano, but it came without the stock motor. I decided to upgrade to a quad motor 2204 instead. The fuselage firewall is buried in foam, so I didn't want to risk damaging any of the foam when installing the new...

This version is tailored for the mid-sized model, not the full-fledged Skyhunter or the Nano.\r\n\r\nThe mount is positioned above the wing and utilizes the screw that holds the wing in place. It features two spots to securely attach a camera via...

This quick design is intended for an RMRC Recruit, accommodating a Matek VTX-HV module alongside virtually any 30.5x30.5 Flight Control board and a compact GPS unit. To avoid obstruction of the USB port, it's suggested that standoffs be used to...

This is a basic 5mm LED holder for the RMRC Goby 210, attaching to either side of the main frame or on the narrower deck area.\nNote: It has a pre-drilled hole for fitting the flange on the LED, allowing you to install it either way to adjust how far...

Quick and dirty replacement top plate for the Hellbender 204 from RMRC. Clearly a makeshift solution, but it gets the job done until the genuine carbon fiber part arrives from UPS. ... Check out this fantastic, practical, and budget-friendly frame in...

GoPro Mount for RMRC GOBY 180 30 Degrees Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: Enabled with a Thick Bottom Layer Supports: Not Required, But Can Be Added if Desired Infill: Set to 40% Density for Optimal...

A Remix of a plattform for the skyhunter 1800 for the Dji AirUnit

Some custom cooling panels are designed specifically for the compact SkyHunter wing compartments.

A Remix of a plattform for the skyhunter 1800 for the Dji AirUnit

This is a custom mount for the RMRC Recruit, designed specifically to accommodate an Insta360 One where a GoPro would typically fit. To make it work, you'll need to modify both the lid and the front cowling of the mount. Additionally, reinforce the...

Mount your RMRC Cricket video Tx to the back of your Shen Drones Tweaker frame with ease by using this design. To get started, simply flip the model 180 degrees before printing because some people may need extra help. Recent updates have taken place,...

Remix of https://www.thingiverse.com/thing:4011721 scaled for the Mini Skyhunter, and trimmed to reduce weight.

This is a quick design for a RMRC Recruit. It holds a Matek VTX-HV, just about any 30.5x30.5 FC, and a micro GPS unit. The FC and VTX are on the same level so the usb plug is blocked. You may want to use some standoffs to raise the FC so the usb port...

Tired of your front hatch poppin off on your Skyhunter when you land. ...Skip them embarrassing moments when your spot landing and your friends are laughing at your gimbal and camera flying off.

Fed up with your Skyhunter's front hatch popping open every time you touch down? ...Ditch the humiliating encounters where your landing spot becomes a comedy show, with your friends cracking up at your gimbal and camera going haywire.

These are the parts I tweaked or designed (with the exception of the Drift Scoops which were already created and perfect) to use the FPV Combat system on my Skyhunter Racing model with DJI Digital FPV.

My SkyHunter 1800 will be a twin motor setup. I designed this mount (work in progress) to hold a FPV video transmitter. ... Working on revisions but figured I'd post this.

This remix is the same design as original made for use with 2 mm carbon rod on the Skyhunter 1800 mm. But the base is slightly thinner (around 1 mm) because I find the original design too thick. ... Printed in ASA just for temperature resistance in...

This is a 3D-printable dovetail saddle to mate the iGuider with the SkyHunter portable. iOptron incorrectly spaces the provided saddle mounting holes (30mm vs 24mm on SH) which prevents using the original aluminum part. ...With this part you can use...

This bracket allows for mounting the ASIAir Pro/Plus/Mini directly to the iOptron SkyHunter portable extension pier. Works best if printed with <0.2mm layers using ABS filament. ... Requires using the 2x M4 screws included with the ZWO saddle, as well...

The SkyHunter UAV Mount Kit is a comprehensive package that comes equipped with the ADTI Survey Lite Camera Holder. This cutting-edge system enables users to capture high-quality images and videos from unique perspectives, opening up new...

The Skyhunter Main Gear STL I designed makes launching my 1.8M Skyhunter easier. Originally, I used the nose gear STL from Finwing that they provide for their Albabird model. I tested this gear with my Skyhunter swinging a 13" prop and it worked out...

You can find all the information in this article on my website: http://www.sop-fpv.com/tecnologia/item/28-mini-skyhunter-vtol-y3-parte-i, and http://www.sop-fpv.com/tecnologia/item/29-mini-skyhunter-vtol-y3-parte-ii. Edit: I have replaced the...