rlc 2 3d models
865203 3d models found related to rlc 2.
thingiverse
The Reolink RLC-520 ip-camera, although being a POE model, has three cables attached to it. It's quite inconvenient to mount this camera with all those thick connectors attached to it. I didn't want to drill a 30mm hole in the wall. I created...
prusaprinters
The Reolink RLC-410-5MP ring mount can be used as an alternative way of mounting your camera when used in tight spaces. This camera model by default comes with a wall mount that is attached to the rear of the camera body and this makes the camera...
thingiverse
The design was tweaked to nearly double the height of the initial wall spacer conceived by Kneival, while incorporating a deliberate notch for secure LAN cable routing.
thingiverse
Thing Files contain a PDF titled "Instructions". This document contains a parts list, printing specifications, construction and wiring instructions and the necessary information to install the servo. ... The other two documents provide the Arduino...
thingiverse
You can use this cover to protect your lens from Raindrops. Top and Bottom parts can be screwed together. ...
thingiverse
Just two shorter version of the original design. One with a hole for cable routing though the back and another with a side hole for the cable. ... Support for the side hole is preferable.
prusaprinters
This model is a Reolink RLC-811A Camera Mount for 5" Dutchlap Vinyl Siding. ...It will print with no supports.</p><p>I needed a sturdy mount for outdoor use so I printed with 4 perimeters and 4 top and bottom layers out of ASA.</p><p>Mounting...
thingiverse
... I'm including 2 more files. One is a simple insert that should be quick to print, but does lead to more slop in the fit. ...The other is a looser version of the final design; you can use if the you're having problems with the fit of the first file.
thingiverse
Reolink Camera Spacer Delivers. It Keeps Cameras at Bay, Allowing Cables to Sneak Behind Them with Ease. ...Scanned and Converted into an STL Model, Edges May Be Rough But Functionality Remains Intact.
thingiverse
Customized version of https://www.thingiverse.com/thing:1444112 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1444112
thingiverse
Used to mount security camera on outside corner. Contains box to hold wires. Designed for M6 Square Nuts. ...McMaster Part 96887A121
thingiverse
To conceal all cords from view. ...Utilize PETG when deploying outdoors.
thingiverse
Modified GabrioB's base to fit my home's somewhat acute (~67.3*) soffit-to-wall angle. Disclaimer: I'm no 3D modeler, and this is my first time using Fusion360. I usually just derp around in TinkerCAD when I wanna make or modify stuff. When I get...
prusaprinters
This is a modification to a reolink wall mount, to fit my use case of mounting my camera on a 3cm thick board/ fence. ...I just added another plate and a top bridge/ panel so the camera can sit around where the top of the fence is.
thingiverse
Attach the mount securely to the 90mm drain pipe using a few sturdy cable ties. ...Next, insert the screws into the corresponding holes in the mount and tighten firmly until they are snug against the camera.
thingiverse
This CCTV camera is great, but 360 degree turning is almost lost on a flat wall mount. ...This corner mount gives much more view around the property.
thingiverse
Customized version of https://www.thingiverse.com/thing:1444112 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1444112
thingiverse
Customized version of https://www.thingiverse.com/thing:4776769 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4776769
thingiverse
I acquired a Reolink 423 security camera, which boasts a remarkable ability to rotate a full 360 degrees. For me, installing it on a standard wall would have been a waste of its capabilities since I could only utilize 180 degrees of its rotation...
thingiverse
This design is remixed from https://www.thingiverse.com/thing:5536222 It is designed to be mounted on an Ikea pegboard. I chose 20% infill in the bottom part and 100% infill for the top arms so they wouldn't easily break. Used Tree Supports for...
thingiverse
I needed more mounting options for my Reolink camera for perfectly tie to a 503 box in my house setup, so I redesigned it in Fusion 360. I also changed the ribs around the threaded holes a bit to free more space for cable management. This is a bit...