rines 20 3d models
198109 3d models found related to rines 20.
thingiverse
This is a joint for 20x20 aluminum frames. ... The PC in the photo is an example of using this component. *Assuming the following parts are used. ・M5 nut ・M5 T type nut ・Bolt with M5×10 hole ・20×20 aluminum frame
thingiverse
This straightforward clamp secures a Bowden tube to any 20/20 extrusion by utilizing a plastic cable tie. ...To assemble, simply use a cable tie (I employed the spares that came with my FT5), a 3x10mm hex head screw and a corresponding T-nut.
thingiverse
... using the Customizer tool at http://www.thingiverse.com/apps/customizer/run?thing_id=50437. ...To create this version, settings such as Block Height (set to 1), Block Width (20), and Block Length (also 20) were employed for the printing process.
grabcad
A 20 Doge coin is ready for take-off, headed to new heights! Here's the wallet address to send your digital currency: DPKEKvG3jDdfT3wPSadNYdfQuw8i5mVLxX. ...Get ready to blast off!
thingiverse
Cable Holder for 20mm Extruded Aluminum to Secure a 1/2" Split Wire Loom with 14mm Diameter Loop Print Settings Supports: No Infill: 15-20% Notes: Trust Your Printer Expertise, Adjust Settings According to Your Machine's Capabilities
thingiverse
......I've tweaked the design slightly and made a mount to fit on a 20/20 extrusion using M4 bolts. All hardware is as per a standard Wade's Geared Extruder, detailed on my other listing (http://reprap.org/wiki/Wade%27s_Geared_Extruder#Non-Printed_Parts).
grabcad
This 20"x20" Devlieg Type M Air Lift Index Table Rotary Table features numerous specifications, including 4 parallel tee slots, a cross reference slot, 4 lock bolt positions at 90 degrees, and 360-degree table graduations with 1-degree increments.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: motor_shaft = 4 m3_dia = 3.2 pulley_b_ht = 0 no_of_nuts = 1 additional_tooth_width = 0.2 idler_ht = 2.5 nut_angle = 90 teeth = 20 profile = 6...
sketchfab
The high-precision PBSS Series offers a spline size of .787 inches and a shaft diameter of 20. This is achieved through a unique combination of advanced materials and precise manufacturing processes. ...The result is a reliable and long-lasting...
prusaprinters
A simple ruler of 20 cm long. Print instructions2 colours: 1 for the ruler and 1 for the numbers obtained with filament change. I added a name and a drawing (both extruded) for the one I printed.
cults3d
Just a simple spool holder for any printer with a 20/20 aluminium extrusion frame. You'll need a M8 bolt at least 30 mm long, a couple of M8 nuts and a 608 bearing. It does not have a filament retainer, but I didn't find it to be a problem. There's...
thingiverse
A Simple Spool Holder for Any Printer with a 20/20 Aluminium Extrusion Frame Requires Minimal Materials. A M8 Bolt at Least 30 mm Long, Alongside Two M8 Nuts and One 608 Bearing Are Essential Components. This Design Does Not Incorporate a Filament...
thingiverse
I have experimented with these prints, discovering that a layer thickness of 0.15 mm provides optimal strength.\nPrint Settings\nPrinter Brand:\n MakerBot\n \n Printer:\n MakerBot Replicator 2X\n \n Rafts:\n No\n \n Supports:\n No\n \n Resolution:\n...
grabcad
A 20-litre container holds contents, unfitted with a valve for liquid passage. ...With the bottle filled to its full capacity of approximately four cubic meters, the container measures around 96 centimeters tall and boasts a diameter of about twenty...
pinshape
Designed specifically for mounting on T-Slot type extrusions such as Misumi, 80/20, OpenBuilds, etc., this housing features a 30° tilt for enhanced accessibility post-mounting on the printer. The snug fit ensures a mere 0.1 mm clearance all around...
thingiverse
This mounting device is specifically designed for attachment to a T-Slot type of extrusion, such as Misumi, 80/20, or OpenBuilds. It boasts an adjustable angle tilt of up to 30 degrees, allowing easier access after mounting the printer. Its precise...