right oculus quest 2 controller 3d models

Stock, the Oculus Quest2 does not fit me very well. If I pull the band low enough to keep it from slipping off, there is a huge gap at the bottom of the headset. This print allows me to have a very good fit with no gaps and keeps the headset well...

5 walls, 0.1mm, x2 infill lines, triangles, 20% infill Cut Oculus Strap as close to the old clip as possible. Melt the cut end until there is one solid line of plastic on the end on the strap, for strength reasons. Print the new clips and use the...

Cable clip for your Oculus Link cable, just snaps onto the side of your headset. This helps relieve stress of the very strained and weak USB C connector on your headset. Best printed in ABS or PETG but can be printed in PLA and will probably work...

Print replacement straps for your Oculus elite (with or without battery) strap. There are three versions included:One piece original size (needs bigger print bed)One piece Prusa MK3 bed size (should fit most heads but may be tight if glasses...

The internal grooved one should accommodate a official Oculus Link cable. The top edge cable holder is a little larger in case you want to hold a headphone cable also. You may need to file down the opening a bit, if it is too small for your...

Works with the same 5x2mm magnets: https://www.amazon.ca/gp/product/B08H1N2HRJ Zenni Glasses to use: https://ca.zennioptical.com/p/metal-alloy-full-rim-frame-with-spring-hinges/5500?skuId=550021 The other remix increased the height of the parts that...

Link to battery holder V2 with a more secure design and less "moment" weight so it feels lighter than V1: https://www.thingiverse.com/thing:5250979this is a remix and my first design so that you can have a power bank plugged into the oculus while...

Link to battery holder V2 with a more secure design and less "moment" weight so it feels lighter than V1: https://www.thingiverse.com/thing:5250979 this is a remix and my first design so that you can have a power bank plugged into the oculus while...

.2  2 layers concentric infill

another quick and dirty remix. ...I failed to print upper hook but it works quite well for a controller: https://www.thingiverse.com/thing:5012721 remixed from https://www.thingiverse.com/thing:4699963 which is under CC-BY, by AlexKapa94

This 3-file OpenSCAD project is a remix of the excellent "Oculus Quest Magnetic Prescription Lens Adapter" project by jegstad: https://www.thingiverse.com/thing:3659124/ Two of the three included files are unmodified from the version V2 of that...

This wall mount set is designed for the NEWZEROL elitestrap, but i think the original Strap fits also very well. ...You can easily grab and hang back your controllers. To attach the set to the wall I used 6 x (4mm x 30mm) screws. ...

The headset mount is a remix of a design from lensfort on Thingiverse that allows me to hang it on my pegboard: https://www.thingiverse.com/thing:4630669The controller mounts are an original design.You'll need support material to print the hooks for...

remix grip from https://www.thingiverse.com/thing:4651978 608 2RS bearing * 2 20mm magnet rubber band M3 bolt nuts

See it in action here: https://youtu.be/9jmVSX2XWIg I recommend you coat the inside of the paddles with a thin layer of hot glue, this prevents them from scratching your controllers and makes them more grippy. ... Composite version: Parts: 3d...

... "Mike vom Mars" https://www.thingiverse.com/thing:4025967 there is a carrier for the glasses and the stand, additional there is a carrier for the Elite battery pack. The controller mountings have been slightly extended to make them easier to use.

If you've already printed the VR Headset Holder found here: https://www.thingiverse.com/thing:5498909 but you've added heavier aftermarket Headset Straps, External Batteries, etc, to your VR Headset which has increased it's weight, this Add-On Brace...

... is a carrier for the glasses and the stand, additional there is a carrier for the Elite battery pack. The controller mountings have been slightly extended to make them easier to use.

Cable ties are no longer required.Thickened the thin parts to increase strength.I put the left and right in one file.2023/10/19 Uploaded the inverted version2023/10/16 Have created an object that is 10 times larger than the previous file. ...Please be...

This model requires a 1.5m hook-and-loop fastener. ... You should cut the hook-and-loop fastener to 5pices. 3 for the battery - mount, 2 for the mount - strap. ... The battery must be mounted upwards.

... the layard. To install the layard: first put the lanyard in the hole, then loop over the clip and secure it in the 2 little hooks on each side. See photo. That how I install it but may be you will an other way haha. ... Print it flat, it's easier

UDATE 2: Re-Meshed the wings “conector” in blender, the V2 was made measuring the physical model, while this V3 is made by using the virtual model, allowing for a perfect fit with the base, they both work equally well, but it might be easier to align...

... Then loop over the clip and secure it in the 2 little hooks on each side. See photos. ...That how I install it but may be you will find an other way haha.Print it flat, it's easierPrint SettingsRafts:NoSupports: NoInfill: 100Filament: PLA Grey

There are 2 versions of this, one with AND one without secure tabs. Designed in Fusion and printed with Windows Print 3d using ABS. The rims for both are beveled. 1. Without Tabs - Just press the O into the rim. The rim is beveled and is...

"Coin-Loaded" Controller Mount for Oculus Quest/Rift S. This is the ultimate version of our popular accessory. Demo video: https://www.youtube.com/watch?v=swoUBkZu2KQ I engineered this mount to print with no support required, making it a seamless...

Wall mount for Oculus Quest controllers (Oculus Touch). Securely attach mount parts to drywall or plasterboard using #10 mini stapler needles. The ingenious idea behind this project comes from Kabebijin products, a company that has truly pushed the...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi, but the adapter is movable, so I decided to make it 2mm longer and added a small clip at the end, so it does not get off...

I was inspired by lensfort‘s Oculus Rift S or Quest Controller Wall Mounts and the unique way he secured the controllers using gravity. https://www.thingiverse.com/thing:3678073 However, I am a minimalist kind of guy and wanted to capture all the...

I was inspired by lensfort’s Oculus Rift S or Quest Controller Wall Mounts, specifically how he utilized gravity to secure the controllers. Check out his design on Thingiverse: https://www.thingiverse.com/thing:3678073. As a minimalist, I wanted to...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi (https://www.thingiverse.com/thing:4624192), but the adapter is movable, so I decided to make it 2mm longer and added a...