rifle bag rider 3d models

This design is intended to help support your air rifle on a support bag to keep it steady during competitions or while hunting. Please come check out my channel Copper State Outdoors on YouTube! www.YouTube.com/CopperStateOutdoors If you...

MDT oryx bag rider one is more flat and the other is more round

This is a bag rider for a Foundation Centurion stock. ...It leaves a gap for filling in some attachment method.

... share it with you. ... To make the bag rider, I used the following Thingiverse items: This is what I used to build the Picatinny part: Weaver/Picatinny Gopro mount by Dansto is licensed under the Creative Commons - Attribution - Share Alike license.

First production run of a custom M-Lok Bag Rider designed specifically for use with MDT buttstocks. ...Measurements are precise, with units as small as 0.001 inches requiring a significant scaling factor - approximately 2,540% - when working with metric...

Made this to give the rear of my Magpul Pro 700 chassis little more reach to my rear bag. Fits snuggly on the rear with 2 x M-Lok attachments. Edges on the top help to center the part on the chassis. ...

Gives a wide flat section for rifle to ride on benchrest or sandbags, and prevents damage to sandbags from handguards. I used the Braudel T-Nut and Screw set. They are metric, not real M-Lok spec hardware, but significantly cheaper than the real...

A user of the GRS Bifrost Stock has discovered that the standard stock's picatinny rail is not ideal for shooting bags. To address this issue, a longer version of the stock has been designed, which fits comfortably under the butt pad when collapsed.

bag rider for Brk ghost

This is a straight bolt on to replace the picatnny rail on the bottom of the Tikka Tac A1 butt stock. ...It uses the original screws to attach. The bag rider works a lot better with a rear bag than the original piece of rail that the rifle comes with.

A sleeker rendition of the bag rider for a GRS Bifrost rifle stock caters to those seeking a "tacticool" appearance. ... Note: Following extensive testing, this configuration performs remarkably well on bags; however, it conflicts with the sling when...

Updated version of my previous Bag Rider. ...This one can be printed at 100% scale as it was exported in mm.

Updated version of my previous Bag Rider. This one can be printed at 100% scale as it was exported in mm. ...

The angled bag rider works seamlessly when paired with finly adjustable bipods (f-class) or a precise rest, allowing for effortless shotting adjustments. ...In contrast, using distinct bipods of varying heights (harris/versapod) with the flat bag rider...

hello, here is my adjustable bag rider for the KRG Bravo chassis it use the same mecanism as the cheekriser all you need is: - 2x8mm rod ( you have to cut to lenght) - 1xM5x25 screw ( from the Bravo chassis) - 1x flat nut ( from the Bravo chassis)...

... don't market theirs as for specific Bravo's. It fits very close to the way that the KRG one does. You'll have to source hardware, which I cannot help you with the sizes because I ended up buying a KRG bag rider before finding the necessary hardware.

This is a bag rider model that fits well with MDT Oryx chassisIt is a remix from this thing: https://www.thingiverse.com/thing:4139775When printing, use 50%+ infill and walls 3mm, and position the model on a side for printing without supports

Bag rider for the Ruger Precision Rimfire. ... This is a tight fit on the pic rail on the bottom of the buttstock, there is a hole in the side that can be threaded for an M3 screw to use as a lock pin

This front bag rider is specifically designed for use with a GRS Bifrost Stock, providing a convenient and secure mounting solution. Built to integrate seamlessly with existing stock mounting points, this accessory offers a sleek and functional...

Adjustable bag rider for the SKOUT Epoch which utilises 4 holes under the rear stock.As with all 3D printed holes, much is depended on your printer/filament settings and how good your printer is tuned but there should be enough space for a ¼"-20...

A slightly longer version of the wombatordnance tikka bag rider

Angled bag rider for the KRG X-Ray rifle stock. Replaces the standard block using the standard mounting screws. ... Works better if it's printed bag face down as it is smoother, it might require some supports in the screw hole counterbores.

Angled bag rider for the KRG X-Ray rifle stock. Attached using the standard screws but gives a longer angled face. Print with the bag side down for a smoother finish. ...You might need some supports in the screw hole counterbores.

I designed this mount to add the Cadex rear bag rider to my Tikka T3x Tac A1. ... You'll need 1* 8-32*1" bolt and the nut that goes with it to be able to mount it on the rifle.

Drawing based on my Aluminum MDT bag rider (fixed) but ported for m-lok mounting.

Solid and efficient Bag Rider Thanks for posting all make and any feedback is appreciated, ideas for evolutions, improvements...

The bag accessory from Ariel Rider attaches using parachute clips around the top tubes. It's a bit unstable. This platform clamps to the top tubes and provides a stable platform for the bag. The bag still attaches using the parachute clips, but...

... into the system. ...The bag rider is strategically positioned to fit snugly within the MLok slot, providing a secure attachment point. ...It securely attaches using 10-24 flat head hex drive screws and square nuts, guaranteeing a rock-solid connection.

This wedge-shaped bag rider securely fastens to the KRG X-Ray chassis, employing the identical holes and bolts provided with the chassis to firmly attach the picatinny rail to the rear of the stock.

... on so there's no need for a clamp. I printed it standing on its end so there was no need for supports and gave it a light sand when it was done to smooth it out. The bag rider has a hollow underneath and 2 rails on the sides to slide on the bag.