ridgid table saw featherboard 3d models

Model includes T-nuts and knobs for M6 screws to fix it on the table sawI printed featherbaord with Prusament PLA Pineapple Yellow (Similar color than Dewalt one). T-nuts and knobs in Galaxy Black</p><p>Nothing special for printing. ...Just remove...

I have found that the star bolt get in my way when cutting narrower items and am redoing this featherboard for the 5/16" flat head bolts to go through the front of the featherboard and the star nuts to go on the back side. ... Revised items will be come...

and tightening these two bolts using the thumb screws both applies pressure to the feather board itself to stay in place and spreads the two angled groove inserts against the table saw groove to apply pressure against the slot to hold in place. My...

Busted the knob on my trusty Ridgid table saw - now I'm on the hunt for a replacement, but it's nowhere to be found, so I'll just have to whip up one myself.

Remix of a good model, T-Track Table saw track by P3X. Had to reduce width to 19.05mm to actually fit and slide easily. ...The holes are sized for 1/4in hex head bolts to mount pieces to, such as featherboards.

My table saw mine is 20-25 years old, alsosame as many old craftsman saws. The fence guides found on thingaverse would not work, so I made my own, These will get rid of the wobble and tighten your fence. Supports are needed , you will need to print...

This design is a remix to adapt a featherboard to fit a DeWalt portable table saw. The main body is the 6 mm featherboard with no changes. The main body is larger than necessary with my DeWalt portable table saw. The 'MINI' is smaller and will...

... Additional information about this project can be found on my blog at https://makeverse.home.blog and specifically at https://makeverse.home.blog/2019/03/02/featherboard-for-bosch-pts10-table-saw/. ... I hope you find it enjoyable.

RIDGID ShopVac table saw hookup, Table saw has a 2.5" OD and the would not hook into my 9Gal Shopvac. Well now it will.. ...nice slide on fit to ensure the best suction while cutting.

The nut from the original post was too big for my saw so I redesigned one based on the dimensions of the miter slot on my saw.After that I decided that the featherboard itself was a bit short so I lenghtened it by 5mm. I also increased the diameter...

I wanted to hook up my Ridgid Shop Vac directly to my new Ridgid Saw Table. The table has a 4-inch outlet, while the shop vac's outlet is about 2 inches. This creates a pretty tight squeeze. I secured it with duct tape since it'll be there...

Riser bevel gear for ridgid table saw ts2400

Replacement Wheel for Ridgid R4516 Table Saw. ...Printed in two parts for simplicity.

I had a specific problem to solve: Ridgid 15A Compact Table saw (R4517) + corded Ridgid vacuum for dust collection on the same electrical circuit. = Tripped circuit a plenty! Unfortunately my work area doesn't have a separate circuit. So in the...

This is an exact replica of the plastic clips originally attached to a Ridgid TS3650 Table saw fence. Due to their unavailability from the manufacturer, any damage or loss can render the fence unreliable. ...The following model has been printed using...

&nbsp;Fixes the slight wobble in the ridgid table saw fence before you clamp it down. &nbsp;It replaces the two white plastic parts on the bottom of the table saw. &nbsp;</p><p>If you use it let me know! &nbsp;it's a work in progress. &nbsp;I believe...

... when the featherboad clamps are screwed down, it locks onto the bed. Here's the type of featherloc it fits (using the M6 T-bolts, not the countersunk bolts). https://www.amazon.co.uk/Featherboards-Spring-Router-Tables-Windows/dp/B01DBYGV8G/

TAKE ALL SAFETY PRECAUTIONS REQUIRED AROUND A TABLE SAW IMMEDIATELY To cut the zero clearance slot: * Switch off the power * Remove the old plate immediately * Lower your saw blade to its lowest position * Locate the tab on one end of the plate and...

I created a fantastic featherboard a few nights ago, but unfortunately, I've lost track of it now and can't give proper credit where it's due! Initially, I intended to fabricate some T-nuts, but then I thought I'd try 3D printing instead - so far,...

Ridgid Shop Vacs, a Home Depot brand, feature an unconventional hose size that makes them incompatible with most Table Saws. ...This adapter solves the problem by enabling you to connect the vac directly to your saw.

This is a zero clearance throat plate for Ridgid R4512 table saws. These may or may not work on R4520 saws? I believe they are the same but I do not own one to verify. Because the print is too large for most printers, it must be printed in 2...

This is a zero clearance throat plate for Ridgid R4512 table saws. These may or may not work on R4520 saws? I believe they are the same but I do not own one to verify.</p> <p>Because the print is too large for most printers, it must be printed in 2...

After some research, I saw and became very envious of the SawStop's blade guard dust collector. I wish we had something similar on the Ridgid. But my saw also didn't cost $2000+. There is one commercial solution, but lead time was 2-3wks and it...

See the upgrade: https://www.thingiverse.com/thing:4775386 Since the " T slots" for my table saw, are smaller than a "regular saw", I was forced to use small bolts sizes. M5 was as big I can go, anyway... for those who own a Bernardo saw ... and see...

Remix of this https://www.printables.com/model/494391-kreg-accu-cut-garage-door-holder-with-screw-nob/files. ...With new knobs. It holds the Ridgid Track Saw Track. ...Need 1/4-20 heated inserts and bolts.

This is a Track Square I designed to work with the New 18v Ridgid Track Saw (r48630b). You will need to get some ¼-20 T-track bolts; I will link to the ones I used. I also used m3xm6 heated inserts with m3 screws to attach the bottom. And of course...

Featherboard for the circular saw for mounting on the fence and the sliding table on a Felder/Hammer K3/B3

22.5 Degree adapter from any DEWALT table saw to standard Ridgid shop vac hose.

I liked the edits on the featherboard done by r00nee, but the miter bars didn't fit in my Ridgid table saw miter slots, so I edited in order for them to fit. While I was at it, I changed the bottom of the bar to hold either 1/4-20 Hex nut or...

I liked the edits on the featherboard done by r00nee, but the miter bars didn't fit in my Ridgid table saw miter slots, so I edited in order for them to fit. While I was at it, I changed the bottom of the bar to hold either 1/4-20 Hex nut or 3/8-20...