ridgid table saw dust collector adapter 3d models

While building my blasting cabinet I needed an adapter to hook up a dust collector, so I created these models to make it possible. ...they are for a 1 ½" schedule 40 PVC elbow.</p>

Ridgid Orbital Sander dust port adaptor for Rockler's flexi-hose.

Made this adapter for my 2HP General Dust collector, that I'm converting for use with a canister filter. It adapts the 8-hole rectangular blower output to a standard 6in hose. ... Hole spacing is 3.1in / 3.57in Printed with 0.8mm nozzle at 0.3mm...

... of tools. ...but I believe shop vac hoses are pretty standard at 1.75". The dustport on the table saw is a little strange at 2.55" I printed it with solid infill but I'm sure it'd be fine otherwise. ...It's a bit thicker than most adapters at .095"

I'd be happy to create a Simple Adapter for your Dust Collector that converts from 31mm to 41mm. There are two versions: First, there's the straight version that goes directly from 31mm to 41mm. ... Next up is the tapered version, which adjusts...

Simple Adapter for my Dust Collector from 31mm to 41mm. There are twi versions: One is Straight 31mm and 41mm One is tapered form 30mm to 31mm and 40mm to 41mm Category: Hobby

This is a 4" dust collector connector for a down draft table, or anything else that could use this.the low profile of this allowed me to make a relatively low profile table that is 4" high.I printed this with PLA, rectangular face down no support.

This lets me plug Ridgid's 1 7/8" pro vac hose (the flexible swivel end) into a Veritas Magnetic Dust Chute from Lee Valley. I designed it for ABS and the slight shrinkage it has. You may or may not want to scale it down by 1% if you're printing...

Replacement/upgrade outlet adapter for the Harbor Freight 2HP dust collector that seamlessly integrates from the rectangular opening on the collector to 6" flexible hose, an upgrade from the 5" size of the stock adapter. The rectangular end boasts...

This adapter connects a 45mm Shop-Vac hose to a Kent CNC dust collector with a 4" diameter vacuum port, featuring an interior thread for snug fitting. The other end allows push-fit onto the 1.75" Shop-Vac hose. Designed in SolidWorks, it was printed...

I've made this to improve saw dust collection from my Rebir IE-5708M planer as the original one is too small and causes constant jams.

After everything is in place I ran a bead of silicone around the joint between the wall and the hose adapter, and also along the bottom of the shroud since the surface of the table is uneven when you have the 90 degree stop attached to the sander...

Dust collection port adapter from a Central Machinery (Harbor Freight) 9 in benchtop bandsaw. ... Includes adapters for a 1.25 inch hose used by the ShopVac micro as well as the Festool 27/35 hose.

I had originally intended to drill a few holes in the wings, then bolt some velcro straps onto them, but fortunately, this dust collector hose friction fits perfectly onto my low-rider 2 machine. There are intentionally small gaps between the hose...

... adapter and scaled it for a 2" vacuum hose. Recommend doing a test print of a section of the hose adapter to check the fit. Adaptation of: Dust Collection Hood 50mm Hose by Luwayne Published on January 24, 2019 www.thingiverse.com/thing:3378710

I took them both off the saw to connect it to a dust collector and have since lost them both. It also turns out that when you buy a new bag, you also need to buy the adapter. Or, y'know, just 3D print one. This was made for my LS1017L saw and dust...

Since the first adapter did not fit my application, here is another vacuum adapter, this time angled at 35 degrees and made a but slimmer. Ideal for dust collection systems on CNC Machines, Bandsaws etc. Holes are for M6 Screws, fits 34mm Vacuum...

An adapter to connect my Sealey vacuum hose (link below) to my dust cyclone. I used the middle sized connector from the ones included with the hose. ... https://www.amazon.co.uk/gp/product/B000RA0LOI/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1

This allows you to connect the dust port from a Kreg K4 pocket hole system to a Ridgid wet dry vacuum (specifically the WD4070). Recommend using PETG. ...I used the following print settings: Layer Height: 0.3mm Perimeters: 4 Infill: 20% ...

This is a remix of ShapeLabs's track saw hose deflector design, which was then updated by Mak-E-Verse and made compatible for Makita tracks/rail guides. Both original designs are based off of the Festool FS-AW available for their rail guides. I...

Connects a shop vacuum hose to the guard of the radial arm saw, replacing the cast swiveling discharge elbow. The inlet side has a groove to accommodate the set screws that retain the original. They can be left slightly loose to allow the new elbow...

This allows a 4 inch dust collector hose to be attached to a low rider 2. I had originally intended to drill a couple holes in the 'wings' and bolt some velcro strap on, but it seems to friction fit on the machine fine for me without the need for...

This is a remix of ShapeLabs's track saw hose deflector design, which was then updated by Mak-E-Verse and made compatible for Makita tracks/rail guides. Both original designs are based off of the Festool FS-AW available for their rail guides. ...I...

This lets me plug Ridgid's 1 7/8" Pro vac hose (the flexible swivel end) into a Veritas Magnetic Dust Chute from Lee Valley.I designed it for ABS and the slight shrinkage it has.  You may or may not want to scale it down by 1% if you're printing in...

Dust collector tube for mini table saw: https://www.aliexpress.com/item/1005002384256758.html?spm=a2g0s.9042311.0.0.3bb95c0ftZv4it It allows you to connect a battery vacuum cleaner, eg BOSCH ProPower 8

... measures 31mm. Verify the fit by printing a few initial layers and then aborting the print job. Inspect that it fits securely onto your hose. Alternatively, test the smaller end by reversing the adapter in your slicer to print the small end first.

... DCS361B. ... Scale up the file by 2540% and print with 100% infill. Takes 45 minutes to print in vase mode at 60mm/s Push it in to the miter saw dust port. Very tight fit. Also compatible with the riving knife dust port on the 60v max table saw.

The Makita Biscuit Jointer Dust Adapter is designed specifically for use with Rigid shop vacuums, making quick work of cleaning up debris from your woodworking projects. ...To get the most out of this adapter, it's essential to hold onto it firmly while...

The Titan Table Saw Dust Extraction Coupling Adapter Enables Users to Seamlessly Connect It to a Standard 32mm Vacuum Hose, Such as the Reliable Titan Wet & Dry Hoovers. Ideal for Indoor Use, This Convenient Accessory Ensures Smooth Operation and...

An elbow dust extractor for my Dewalt Saw Table dwe7485 Designed on tinkercad : https://www.tinkercad.com/things/8vsQtuC56nz