ridgid table saw dust collector adapter 3d models

An adapter between Makita MLT100 table saw and Metabo SPA 1200 dust collector. ...63mm (inside) to 100mm (outside) adapter.

Replaces the stock 2.5" adapter on a Ridgid R4331 planer to use a 4" dust collector hose

... diameter sawdust pipe, whereas my compact shop vacuum boasts a significantly smaller 3.5cm opening. ...To bridge this sizeable gap, I've found an ingenious adapter that seamlessly connects the two, and it's been working out perfectly for me so far.

I made this adapter to make the small hose on a shop vac work with my table saw's dust extraction port. I designed this adapter as simply as possible so that I could print it once and it would just work. ...Both sides are press fit.This was purpose...

Adapter for my Bosch GTS 10 XC Table Saw Dust Port to 100mm Chip Extractor Hose. The outer section of the large side measures 100mm in diameter, featuring a small lip designed to prevent the hose from slipping out. The smaller side tapers gradually...

This is a hose coupler/adapter to fit the Ridgid Shop Vacuum hose to the Ridgid 7-1/4" Compound Miter Saw. This is super-easily modifiable in OpenSCAD to adjust Hole dimension to accommodate different Ridgid Tools as needed. ... OpenSCAD is a free CAD...

This is a hose coupler/adapter to fit the Ridgid Shop Vacuum hose to the Ridgid 7-1/4" Compound Miter Saw. This is super-easily modifiable in OpenSCAD to adjust Hole dimension to accommodate different Ridgid Tools as needed. ... OpenSCAD is a free...

I made it for my Ryoby table saw for adapt my vaccum Karcher WD5 on it. Easy to us and work perfectly. ... Print it without support.

A versatile coupling device designed specifically for connecting the Makita MLT100 table saw to the Metabo SPA 1200 dust collector, effectively bridging the size difference between these two high-performance tools. ...Measuring 63mm in diameter on one...

Designed to connect a Ridgid wet/dry vacuum that connects to 1-7/8" accessories with a Metabo C10FCGSM miter saw's dust port. The end that has an OD of 2.0 is slightly too small. Had to wrap with duct tape to make it stick in the miter saw. ...

Vacuum host adapter connecting a "This RIDGID 15 Litre (4 Gallon) Portable Wet Dry Vacuum" (wheeled) to the exhaust port of a "Mastercraft Sliding Compound Mitre Saw (10-in)". This was created using @Zivbot's excellent Customizable Vacuum Tool ...

Added more options for dimensions to vacuum adapter created by other user. ... Turns out that the 1-7/8" Ridgid vacuum hose is more like 1-13/16", and my Metabo miter saw seems to accept ~2-1/16" or 2-1/8" hoses. ...Trying to get the dimensions correct.

Hose adapter to fit a 14 gallon Ridgid shop vacuum with a 2 1/16" (2.0685") hose to a Ryobi miter saw with a 1.65" extraction tube. It fits well but you can add a bit of thread tape if you want more sticking power. ... Included the model file so it...

I'm Using My Dewalt Planer with a Ridgid Shop Vac Hose Dust Collector Adapter. ...The Hose End Locks Securely into the Planer Nozzle, While the Other End Connects Directly to My Printed Cyclone Dust Collector.

I designed a system to capture sawdust from my Ryobi Table Saw by placing a board beneath it and cutting a hole in its center. Next, I 3D printed a funnel-shaped attachment for my shopvac, which I purchased at Harbor Freight. The design includes a...

Being unsure about utilizing the dust hose adapter located at the rear of my Harbor Freight 10-foot 13-amp table saw, I came up with a custom-designed connector that accommodates not one but two distinct sizes of tubing.

This model has been remixed to fit a Ridgid NXT 2.5" hose (2.25" OD at connector) to a DeWalt Sliding Compound Miter Saw - specifically model DWS780 but it will fit other models. ...Chamfers have been added to the vac locking mechanism and from the...

This is a zero clearance throat plate for Ridgid R4512 table saws. These may or may not work on R4520 saws? I believe they are the same but I do not own one to verify. Because the print is too large for most printers, it must be printed in 2...

This is a shop vac adapter for the Makita SP6000J tracksaw to Ridgid shop vac. The size of the ridgid side is for the larger tube (similar dimensions to the intake of the shop vac). I had to go through several iterations to get the tolerances...

Customized version of https://www.thingiverse.com/thing:1246651Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651

I needed a way to catch all the sawdust flying out of my Ryobi Table Saw, so I placed a board right underneath it and cut a hole dead center. Then, I 3D printed a funnel vacuum attachment that snaps perfectly onto my shopvac from Harbor Freight. The...

I required a method to gather the sawdust spewing out of my Ryobi Table Saw, so I positioned a board beneath it and carved a hole in its center. I 3D printed a funnel vacuum attachment to link my shopvac that I purchased at Harbor Freight. The...

This is a right angle adapter that connects to the dust collector such as a CT26 to the hose.

Hose adapter to fit a 14 gallon Ridgid shop vacuum with a 2 1/16" (2.0685") hose to a Ryobi miter saw with a 1.65" extraction tube. It fits well but you can add a bit of thread tape if you want more sticking power. Included the model file so it...

I adapted this design from Elproducts, modifying the hose size to accommodate a 2.25 hose and adjusting the dimensions from 120x120 to 140x140. ...I created this model using Tinkercad and you can edit it online at...

Makita 2012NB planer enthusiasts will find this adapter indispensable for connecting their tool to a standard 4-inch diameter dust collector hose, ensuring efficient and mess-free operation.

This is a zero clearance throat plate for Ridgid R4512 table saws. These may or may not work on R4520 saws? I believe they are the same but I do not own one to verify.</p> <p>Because the print is too large for most printers, it must be printed in 2...

It's a very tight fit on both the vacuum and the miter saw, though they are not going anywhere. I used some paracord to support the vacuum hose, just to lessen the chance the hose will pop off. Printed with 10% infill, a .6mm nozzle, and .35mm layer...

DWE7491RS Table Saw Bottom Hose Adapter to hook up a Bauer shop vac hose, might work with other models of Dewalt Table saw but havent tested. Might work with other models of shop vac hose. ... The hose connector portion has a diameter of 45.25mm.