ribbon cable cutter 3d models

The ribbon cable clamp provided with the Robo 3D plus shipping clamps the ribbon cable in a U shape, which can lead to broken wires over time. This replacement clamp holds the cable horizontally beneath the bed. To install it, remove one screw from...

Ribbon cables are a pain. To properly route my Pi's camera cable, I needed to make a right angle turn. This clip makes that turn and doesn't crease the cable. ...The cable bend radius is 1mm, which my research tells me is quite sufficient.

Designed this to hold the typical flat ribbon cable (16mm) used with common cameras such as the arducam. This does a nice job of securing the cable to the 4040 mounts and has room for smaller cables to go underneath it such as the LCD cable. ... My...

I've created a customizable ribbon cable guide inspired by http://www.thingiverse.com/thing:52025, which meets my specific needs for installing the cable between the Raspberry Pi and its camera module. The cable holder is designed with a closed end...

Users Expecting Rigid Support Not Bending Stock Ribbon Cables. Printing Parameters Raft Generation: Set to 'Yes' Enable or Disable Built-in Support for Custom Prints: Turned Off. ... Output Resolution Levels Available for Selection: Options Include...

Custom version of the Clip for fixing Ender's wires. ... https://www.thingiverse.com/thing:3839232 Changed to a size that can hold the ribbon cable of raspberry pi camera.

Ribbon cable termination requires a precise fit within pin-header covers or enclosures. Duplicate this setup to ensure correct alignment once assembled. ...This is revision three of our design.

Secure the ribbon cable by clipping it firmly to the controller and then the display on the Ender-3 printer. ...Print your object sideways to avoid using supports altogether.

A Support That Doesn't Bend The Ribbon Cable Like Stock Bands. Printer Settings Are As Follows: Raft Printing Is Allowed, But Supports Are Not Permitted. ...The Minimum Resolution Setting Is Set At 0.14 Mm To 0.19 Mm.

Tuck the display's ribbon cables neatly out of sight using this convenient clip. ...It takes the place of one of the display standoffs, keeping everything organized and tidy.

Hey, let's get it right this time. ...I'm looking to get some custom covers made for the ribbon cables that connect the control box to the LCD display. ...That sounds like a great idea!

Custom version of the Clip for fixing Ender's wires. ...https://www.thingiverse.com/thing:3839232 Changed to a size that can hold the ribbon cable of raspberry pi camera.

Here's My Take on an Ender 3 LCD Ribbon Cable Cover I'm thrilled to share with you the result of my tinkering, and I'd be more than happy to hear about your creations too.

Designed to be printed on its back, use a brim if you have trouble with bed adhesion. ... This one is resized to fit the ribbon cable of a Raspberry Pi camera, per Slapping_Plastic's request.

I designed this bracket because I noticed my ribbon cable was peeling off from the bottom of the heating bed, exposing the wiring soldered terminals to potential damage. ...I also created it because the ribbon cable had gotten in the way of a big...

To keep the flat ribbon cable from a Raspberry Pi Camera secure, create a tiny clip using Tinkercad. Apply double-sided tape to hold it in place. ...You can find the design source at www.tinkercad.com/things/9ATQch0E9Ff-rpi-camera-cable-holder.

I encountered issues with the InMoov Bicep Piston damaging my ribbon cable, so I revised RotGear to feature a specialized channel specifically designed for the ribbon. Next, I had to minimize the size of the Bicep Piston and also make adjustments to...

This is an upgrade for those wanting to upgrade from Icarus 2.0 to 2.1 and want the new ribbon cable holder but don't want to reprint the whole carriage. To do so, cut off 42.0 mm from the old ribbon cable holder and glue this new part in place using...

This design is based on WaveSupportApparatus's Ribbon cable clip for Raspberry Pi Camera and also utilizes the T_Slot_Cover designed by Scott_3D.This clip snaps into the T-slot but still allows cables to be run behind the clip.I have redesigned the...

Tronxy XY-2 Pro Ribbon Cable Guide This concise guide tackles the challenge of a stiff ribbon cable that refuses to bend, absorbing its force with ease. Without this essential component, the connector would be exposed at 100%. Achieving high print...

I took the original idea by "TheToddRod" https://www.thingiverse.com/thing:3378694 and remixed it into a ribbon cable clip suited for the SD Card Extender. ... ...

This is a tiny clip to hold the flat ribbon cable from a Raspberry Pi Camera in place. ...Use a 2.5 mm (x 10 mm) screw to mount.</p> <h3>Print instructions</h3><p>Printer Brand: Prusa<br/> Printer: Mini<br/> Resolution: 0.2mm Speed<br/> Infill: 20%<br/>...

This is a ribbon cable clip originally utilized in the E-Mu Emulator II digital sampling keyboard. My clip, located on the left, sits alongside its original counterpart on the right. ...It functions as both a free-standing clamp and a secure mounting...

A simple clip to hold the Raspberry Pi Camera's ribbon cable flush against the Ender3 Pro's MeanWell power supply. Helpful if - like me - you have your Raspberry Pi mounted at the back on the machine. ... Uses 2.5mm hex-screws to attach.

A simple clip that keeps a Raspberry Pi camera ribbon cable flush to a 2040 extrusion. In my case, I used it on my Ender 6 which has the sides removed since it sits inside a reflective enclosure. Buy Me a Coffee? ---------------- Do you like...

A modification to the ribbon cable has been added to secure the filament feed tube directly behind it, perfectly aligning them as they run parallel together. ...With this revised design, utilizing software such as Inventor allows for later adjustments...

This is a simple spring for holding the ribbon cable of the Anet ET5 (Pro) out of the way. The spring has a lenght of 35 cm (= 350 mm) with an inner diameter of 38 mm. ... The diameter of the spring cross section is 3 mm.

A simple clip to hold the Raspberry Pi Camera's ribbon cable flush against the Ender3 Pro's MeanWell power supply. Helpful if - like me - you have your Raspberry Pi mounted at the back on the machine. Uses 2.5mm hex-screws to attach. ...Print Settings...

The inspiration behind this innovative design comes from WaveSupportApparatus's Ribbon Cable Clip for Raspberry Pi Camera and Scott_3D's T_Slot_Cover. This versatile clip offers a convenient feature: it snaps securely into the T-slot while still...

Summary: Ribbon cable failure due to flexing at the connector is likely the most frequent M200 malfunction. This design snaps securely onto your Z-Temp's housing, preventing cable flexing at the connector. ... Print Settings: Printer: Zortrax M200...