rev control hub 3d models

This part is designed to help prevent disconnects on the control hub. Our team struggled with this and decided to share our solution. This part was designed by FTC Team 8907 - Blue Box Bots. Thanks to...

This is a FTC REV Control Hub and Expansion Hub mount I remixed from TheEV. It holds the Control Hub and Expansion Hub on each side and has cutouts for the USB ports. There are holes properly spaced for GoBIlda holes. There are also holes to mount...

This mount allows you to attach two REV hubs vertically and back to back.

A case to store your REV Robotics Driver Hub. ...Many customization parts are included, as well as a blank base and cover to customize yourself.

This case houses and protects the REV Drive Hub utilized in the First Robotics FTC competition. ...An opening has been added to expose the speaker and tabs added to lock the device in place.

Its a T-Frame for the REV Robotics Expantion Hub.

The REV Driver Hub's USB ports are not easily repairable. This model helps relieve some port strain by not allowing the cables to have wiggle room. I printed it vertically with the ports facing downwards. The mount is attached to the driver hub using...

Designed by Team 247 REBOOT This is the REV Expansion Hub mount. It is designed to have both of the Expansion Hubs to be in a small space. It is double sided to hold both of the Expansion Hubs. You have Access to all ports and different ways of...

Designed by Team 247 REBOOT This is the REV Expansion Hub mount. It is designed to have both of the Expansion Hubs to be in a small space. It is double sided to hold both of the Expansion Hubs. You have Access to all ports and different ways of...

Team 3954 Pink to the Future designed this protective Cover for the REV driver hub. Of course, all necessary connections/buttons are still accessible. There is a small gap (0,5mm) left free to adapt for printer inaccuracy. Because the cover is split...

This is a part that is designed to vertically mount a Rev expansion hub onto tetrix or actobotics C channel. The main purpose of this design was to open up space on my team's robot, as we had mounted our expansion hub horizontally before, so that we...

Our robotics team has two REV Expansion Hubs mounted vertically in parallel along the robot's central axis, mounted to two 15mm REV extrusions. This leaves a 30mm space between the hubs, which is just the right size for our REV 12v battery. The...

This part is to help keep the wire in the REV Expansion Hub. It features a low-profile so it won't take up much space on the robot and it sits flush with the ground. ...It is lightweight and uses a zip tie to hold the USB connection in place.

Housing for REV Robotics Driver Hub for FIRST FTC. Housing is designed to be printed from PLA or other rigid filament. Not as much cushion as TPU, but easy to print. Housing can be assembled as a stand-alone, or mounted to a driver station plate...

... exceed 5.5mm for those M3-0.5. Additional: The distance between the two mounting holes is 144mm. DISCLAIMER: In no way does this case guarantee any additional protection to your drivers hub, but one would assume it’s better than nothing. ...

Then slide some pan head bolts up through the bottom of the rev module, up through the relief model and secure it with nuts. Plug your USB in and wrap zip-ties around the plug. In some cases, the 90° will be too big to be held by the two slots right...

A PC control hub that allows you to turn on your PC with easy access to usb ports. ... Used with the following usb hub and a regular PC power switch: https://www.amazon.co.uk/gp/product/B00OQ0CYFE/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

This hub is for a tighter and less sloppy fit for mounting REV Mecanum Wheels on a 5mm hex shaft. ...

Right-angle USB cable support piece for a REV Robotics Expansion Hub. ...Made by FTC team 8103 Null Robotics.

A vertical Rev expansion hub mount for 2 hubs with a strain relief clip. ... Note that the cord has to be run through the relief, then plugged into the hub.

If you are using the strafer chassis from goBilda then this hub mount plate can be used to place the two Rev Robotics hub in the front. ... You will need an angled mini USB cable to make this work https://www.gobilda.com/strafer-chassis-kit/ ...

These mounts are made for the REV Robotics expansion hub and battery as well as a Moto G play for FTC robots. It doesn't matter which side each part goes on so long as the battery mount is in the middle. ...The phone mount is purposely made slightly...

... sliding off of metal tables and surfaces. ... It uses : Two - M3 x 10mm Hex Cap Screws https://www.revrobotics.com/rev-41-1123/ Four - 8 x 3 mm Fridge Magnets https://www.amazon.com/gp/product/B07CPV7X8Y/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

These mounts are made for the REV Robotics expansion hub and battery as well as a Moto G play for FTC robots. It doesn't matter which side each part goes on so long as the battery mount is in the middle. The phone mount is purposely made slightly...

A quick 3D printed battery holder and expansion hub mount our FTC robot.

A quick 3D printed battery holder and expansion hub mount our FTC robot. ...

A bracket to stick. ...Have fun with it.

This design was designed with the REV Expansion hub or REV control hub in mind. The brace comes in two parts. The bottom is designed to be attached to the body of the rev hub either with glue or double sided tape. It is designed to accept a hex...

These Control Hub junctions are for the Modular pipe system and will work with its catwalks. Check here for all the other parts available: https://www.myminifactory.com/users/the3dprintingmagic/collection/modular-pipe-system Include are 3 versions:...

Both are made for Geeetech GT2560 Rev a+ (possible fit others as well?) Rev 2 is made for Raspberr Pi Zero, also with space for an DC-DC converter. Attached is also a cover with cutouts for 2 x 40mm fans Rev 3 is made for Raspberr Pi 2/3/3B. Attached...