reusable spool 3d models

For the coil, I used 30ga magnet wire and wound enough to fill the spool (I didn't measure the length, but I've included a picture of my wound coil). When complete, it measured 50.8-ohms. The power adapter I used was a Cabletron Systems 120VAC 60Hz...

I would like to clarify that the closure is a remix of a gimmick on thingiverse of which, however, I do not find the link This cover removed the logo and modifying the base is adaptable to other machines IMPORTANT: MAX SPOOL SIZE 200 X 65 I hope you...

... slicer's default support systems. Also I have to date printed out the whole first ring of the bonnet, the wing nut, one of the shoulder screws, and one of the shoulder nuts. I'm currently waiting on a new spool of filament to continue printing.

https://www.prusaprinters.org/ SpannerHands' MP spool holder was used to design the extruder mount, and his ideas influenced my modification. (https://www.thingiverse.com/SpannerHands/about) Walter's printable housing for Printrbot extruder gears...

* Finally, follow Prusa's Enclosure V2 [guide](https://blog.prusaprinters.org/mmu2s-printer-enclosure_30215/) for how to install the PSU externally --- Below are links to the other parts that I used to complete my enclosure build: [Angled heat bed...

This is where I remounted the stock spool holder, though beware it needs to be under 85mm in length which fits pretty much all 1kg spools for the bed to clear it at around 350mm on the Z axis. You will need to drill holes for wiring to be run into...

I have pegboard side panels that ventilate the printer. Pegboard and spool bracket - ARC-peglagoWant to install the X1 stock cable chain? I have the bracket for it. Cable chain bracket for stock X1 chain ARC is free for individuals to use for their...

I've had great success with the overhead filament system for my A8 so I wanted to develop something for the TRONXY along those lines. I decided to try and incorporate a previous four-spool drybox/dispenser into the design. It can weigh almost 10lbs...

Still a SKR v1.3 with tmc´s is cheaper, and youre only missing out on the WebControl if you dont use Octopi) ++++++++ Why the setup with the spool in the front, and board in the back? ++++++++ I like a small footprint, but also dislike a spool on top...

Push the top/bottom button to increase/decrease the desired chamber temperature.Additional prints that I used:my own...

I also made an exploded view drawing to help with assembly.Build can also be found on Thingiverse.Purchase Parts:QTY 12 - 20x6x2mm magnets (used to secure the doors from unwanted sliding and opening)QTY 8 - 6x50mm wood screws (used to mount the...

...++++++++ I like a small footprint, but also dislike a spool on top of the printer (because of vibrations, especially if youre printing higher). So i came up with that solution, and it really functions nice. ++++++++ What will that all cost me? Or...

I would recommend printing this in Fusion Filaments PET: https://fusionfilaments.com/collections/pet-standard-spools - This is not PETG, you'll need a printer capable of doing around 270C to print it. If you can't do PET, I would recommend Fusion...

 A flashlight shining through the slit in the hole is your friend.Insert PTFE tubes into the front of the buffer and route to your preferred spool holder system.  If using an enclosure, this will probably involve drilling holes through the enclosure...

It might be only a temporary stoppage so you could hope for the best and try again later.Dual Colors with a Single ExtruderPrinting multiple colors with a single extruder is really easy.I printed my dual-color prints with a single extruder by pausing...

I set a pause in the print right before the hollow shell is set be covered and poured in Plaster of Paris.(This graphic is from the Roly-Poly Toy page from Wikipedia) ———————————————Print SettingsPrinterPrusa Mini+BrimNoSupportsCustom (see below...

You will need a little over 3 rolls of 1K filament spools to print this. Have some spare rolls on hand in case you have failed prints. Some of these parts will use over 1/3 of a 1K spool. Some of these files can take over a day to print. On some of...

The following is the original text that I published on Thingiverse: Many of us Ender 3 users have noticed that pulling the filament into the extruder from the side, while the spool is mounted on the top, is one of several design decisions from...

You will get probably a whole spool from 2 or 3 drops, one when the spool is new, one when it's half done, one near the end. Too much oil causes bed adhesion issues, but if you only use a small amount it really does help everything flow better. I am...

- Update 5/5/2020 I ran into a spool that didn't fit on the spool holder so I designed a part that slides over the spool spike to hold a spool with as small as 40mm center and 100mm wide. - Update 10/7/2020 [Available...

Using the 2mm polycarbonate panels and with all 6 spools the heating system can reach temperatures of up to 45 degrees Celsius or 113 degrees Fahrenheit in 15 minutes making it perfect for drying multiple spools of PLA at the same time*. It can also...

- Geeetech A10M filament guide REMIX for the Spool holder bracket above (https://www.thingiverse.com/thing:3829316) NOTE: vertical assembly is not recommended if you are using the standard PTFE tubes since the additional bending creates more friction...

You can adjust the pressure force appropriately by moving the “unwinding spool clamping ring”.So that you don't have to constantly use a screwdriver for frequently used screws, I have provided knurled screws that you can print yourself. For each of...

 If the dryer still doesn't reach the desired temp, try moving the dryer's temperature sensor directly into the airflow of a USB fan, and a little higher up than default.I use an 80mm AC Infinity USB fan (claims up to 70C and seem to work fine...

For the implementation of this project, I spent about 2.5 kg of filament, so buy 3 spools of 1 kg at once or one large spool of 3 kg. If your printer allows you to print the entire deck, then you should do so, then you need to specify in the...

Going one step further, we have worked directly with Keenovo, industry leaders in silicone heaters, to develop a bed heater which is both high performance, and safe due to its built-in thermal protection. Spool Holder The on-frame spool holder is...

So I multiplied the mass for each color by the price for each spool and then divided that by 1000g to get the price for each color (dimensional analysis). Then, I added up the prices for each of the colors to get the total. ...The final cost per set is...

Print the shortened spool holder and install it inside the printer. Print and cover the holes with the 3D printed parts. Repositioning of the extruder: I decided to go ALL the way in shortening the filament tube, so I chose the spot you see...

I then used the 250mm acrylic cube as a filament enclosure which simply sits on the top of the enclosure and can hold two spools. I attached some weather stripping to the bottom of the cube to create an air seal to the lack table top.</p> <p>I then...

I recently finished a 750g spool and I'm waiting for the next one ;) I know many people are using bowden machines which would not allow to easily print flexible materials, but maybe you can do it slower and changing a few params so... maybe you could...