retro phone stand 3d models

*Barrel: print standing on the breech, like a smokestack. *<strong>Axle</strong> (2): print with axle tip pointing upward. *<strong>Wheels</strong> (2): print flat. *<strong>Wheel Caps</strong> (2): print with opening pointing upward. *<strong>Spring...

Since this will go in a car, do not use PLA - it won't stand the summer heat. I printed mine in PETG (Atomic Bright White), since it's rigid enough and temperature-tolerant. I do not know what other plastics will work here. Incidentally, the original...

A bolt length of 30mm is as short as I would go, but longer will work just as well, if not better.Work the SuperPINDA Precision Adjuster onto and off of the SuperPINDA probe (or stand-in M8-1.0 bolt) several times to “break in” the part. Depending on...

 If you have an enclosure, that might help.All the prints are done with PETG for strength.Print list with detailsBrown prints:treasure_chest_v2_upper_mid_bodyPrint 1 copy.Print standing end-on (see picture).Make sure the triangles on the holes are...

Model made as 1/35 scale.Dimensions: - After being printed will stand: 85 mm tall, 105 mm wide, 241 mm deep; - Small parts should be printed at 100% infill to make them solid.WHAT WILL YOU GET AFTER PURCHASE?- STL files of Tiger I Tank for printing...

N Scale Train Trestle Display I put together these trestles to use as display stands for N gauge engines. One is 10.5 and the other is 5 inches long, but one could easily be made to any length. It is loosely based on a Great Northern Railway Standard...

The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C and D, Class I, Division...

"DGB" stands for "Direct Gopro body". Literally cutting out the middle man, which is the adapterChangelog v1.5- Removed v1.4 and older files (Rip Stats again)- Main bodies take into account the D1 mini antenna poking out by .1-.2mm- Simplified and...

The bottom stand doesn't allow for the vertical adjustment needed to set the water lever within the filter Body, other than simply cutting the legs to desired height. The side hanger though required a change to grate pattern in the Body so they're...

The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C and D, Class I, Division...

From a tiny necklace to massive totems standing at the entrance of the building, cutlery, dinner wear and everything in between could be used as a lucky totem. In addition to varying sizes of the tikis, they could also be made in varying materials...

Also if higher resolutions and slower print speeds give you better results it is wort the extra print time. You might want to consider rotating the Dile 90° on the x-axis and printing it on its side as the shallow angle of the Dial's face makes the...

sleepdeprecation (Thingiverse) - Their budget friendly headband design helps the headphones stand out even more. u/Meteroson (Reddit) - The F3-8M thrust bearings they added to their build were new to me, but I'm glad I was made aware of something...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-HB-150LED-RT-C is approved for use within environments where flammable or combustible gases,...

N Scale Train Trestle Display I put together these trestles to use as display stands for N gauge engines. One is 10.5 and the other is 5 inches long, but one could easily be made to any length. It is loosely based on a Great Northern Railway Standard...

From a tiny necklace to massive totems standing at the entrance of the building, cutlery, dinner wear and everything in between could be used as a lucky totem. In addition to varying sizes of the tikis, they could also be made in varying materials...

Currently, every slicer except for Simplify3D can handle such files by either ignoring or clipping intersections.Floating Z Gap BlocksThese are four blocks hovering above four standing blocks at different heights. The height gaps are 0.01 mm, 0.1 mm,...

Once standard electrical power is restored, the emergency battery pack will be recharged.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C and D, Class I, Division 2, Group A, B, C and D, and Class II,...

I don't expect it to last or stand up to rigorous use, but it's stayed on there so far. I went ahead and made some wheel spacers, too, because the wheels were pretty sloppy on the axels. I decided to throw these in in case anyone else wanted to give...

You need to print: 1x top ring part 1x left ring part 1x right ring part 1x stand/base 1x cap 3x diffuser The 3MF files was created in Prusa Slicer. I added different options. I recommend doing it with the included supports. With that, you have a...

The pieces (which we previewed in earlier posts) are designed to print standing up, and should do so without need of supports (though it can't hurt to add them if you need to). Stay tuned for more sets and pieces, as well as updated rules for all of...

The concept was originally inspired from the infamous $100 "Isoacoustic" decoupling stands I had used on an old audiophile system awhile back. What sets this design aside from other common open-baffle setups is that it uses fishing wire to mount...

Attention!Since i now work with 'Fusion 360' every part will be redesigned from scratch.Check regularly for updates, they'll be listed here.Ender 3 Control and power AIO modular enclosure: Parts you need to order for this Card reader extender for...

They seem to be strong enough unless you put your weight on them directly but you could also substitute them for ¼" poly-carbonate plate from McMaster-Carr or you could make some fiberglass covers.Orientation: Print all parts standing up so that...

It's called ‘Carl’s Desk', because the original was made for Carl.This is a rebuild for the print tables contest, the 3D printed parts are now orange so they stand out, but you know… It looks great so I'm keeping the orange!The...

Simply work the squares around to loosen it up.If you change filament at the same height as textDep, you can make the text stand out. I like to set <i>textDep</i> to <strong>1mm</strong> and <i>height</i> to <strong>6mm</strong>. Then, I'll print the...

I'd recommend removing any metal jewellery whilst building the circuits. Designed entirely in FreeCAD, I can post up the source files if anybody is interested (typing this+BOM has taken forever!). Also, as I post this, I've only just finished hooking...

The base knife block stands 5in (12.7cm) tall, and accepts 13u of panels. An optional adapter can attach to the bottom which tilts the block forward either 5 degrees, 7.5 degrees, or 10 degrees. Note that I have not tested these in practice, so it...

I haven’t done much testing yet so I’m not sure how well this ESC will stand up long term, or even short term come to that. If you manage to get some real grip from the tyres a 20A ESC without heatsink may not be enough, but I’ll have to let you...

Tuning is fairly easy, and it's even easier if you use an electronic tuner or a tuner app on your phone or computer. Here's an online one that seems to work well: https://theonlinemetronome.com/instrument-tunerTuned too highTuned just rightTuned too...