retractable stairs 3d models

The printed reduction gears in the Gregs had a bit of slop in them - I think a direct drive motor has finer control over the filament feed and retraction. Also, my other (newer) printer uses 1.75 mm filament, so I no longer have to stock up on 2...

I am tired of Bowden filament systems, retraction issues, uneven filament pressure, filament grindings, oozing, etc. Direct-driven extruders are much better (geared or not). Did this as the first part of my project to convert this printer into a true...

Designed to hold the Zeiss with the eyepieces in the RETRACTED position. The lens covers are necessary to keep dust, mist or rain from settling on the eyepiece and reliably prevent (prevented, at least so far) the eyepieces from being joggled...

Set retraction to 1mm @ 25mm/s 2. Set extruder nozzle offset X to -7.0mm. In Cura: Settings > Printers > Manage Printers > Select your printer > Machine Settings > Extruder > Nozzle Offset X Materials Summary =============== 1 x Mellow NF...

please let this deactivated)solid infill every: "0" layersfill angle: 45°solid infill threshold area: 0 mm²bridging angle: 0°only retract when crossing perimeters: disabledinfill before perimeters: disabled (i think if the perimeters are printed...

Instead of navy I used transparent blue for my first print of this to see if the candle light would glow through well. Note that my first two panels had some nozzle drag marks as I used default settings and did not set retraction over edges only to...

To remove the lens from the tube, looking from the bottom of the tube, use pliers to pull downwards on the head of the 50mm locking screw, which will retract the lens locking plunger, then untwist the lens. ## Looking to go shorter? Or shooting...

To meet this goal, our team developed an intricate system incorporating four sturdy yet lightweight components: an angular aluminum mainframe supporting a retractable side support; durable tie-down loops fabricated from steel wire with protective...

Once installed, all you need to do is simply inform your favorite slicer software to retract the first strand 60 mm before advancing the second every time you request a color change. This hotend uses a minimal amount of filament for purging, and...

Easy On-Easy Off. Well, like any other tool, my original X-Leveling Spacers https://www.thingiverse.com/thing:3254069 just seemed to get in the way on my print table after use. I didn't want to "put them away" after use, and didn't want to make some...

This allows the balls to be retracted out of the way when there is no car present in the garage/parking spot. It also keeps the little ones from practicing their tennis / baseball skills on it while there is no car. I decided to do this after...

But this time it's because I'm using a fresh install of Cura, and I simply forgot to adjust the retraction settings for my specific set-up. (I also forgot to add the G-Code for bed levelling! Thankfully I got away with it, since the bed level was...

I was having a problem printing a .08 until I decreased the retract to 1mm from the stock Cura setting of 5mm for the Ender 3. I think the filament just moves too slow and heats back up into the the throat causing plugs. . I print with one bottom...

... I used 70µm and elephant foot compensation in PrusaSlicer - If you can't get the roller bearing to break free, reduce the flow rate in the slicer. I also used maximum retract to reduce "blobs" - Adding a bit of vegetable oil will work wonders

I set the Left speed to 110 and retract to 160. I like to let my prints start nice and slow, Once i make sure i have a few hundred layers printed successfully i start to ramp up the speed I printed all of my parts in Sariya Tech Fast resin, this...

The first three lines are from the original start G-code to help put the rest of the code in the right place: G28 Z ; home Z G1 E-15 F100 ; retract filament M109 R{material_wipe_temperature} ; wait for extruder to reach wiping temp ; jelbert taz6...

Don't forget to change your Retraction Settings! These instructions are as best as I can remember and please use caution and your own judgment. I claim no responsibility for any damage or anything going wrong, everything is at your own risk! ...Print...

Includes the fully configured firmware for the MKS Gen L 1.0 board (based on Marlin 1.1.9) and a tuned Profile for the IdeaMaker slicer (~20mm/s speed, 0.2mm layer height, 2mm retraction). **My goals were to...** o preserve the original look and...

the supports are very thin and requires a lot of retraction to a printer. it is not mandatory, your original supports will do the job as well while waiting for me to improve the supports. And finally, I would like to thank Rey, Patrick and Steeve,...

But you would need a powerful part cooling assembly.My print time for the moon was roughly 60h.LED Strip Mount: Layer Height: 0.16mmWall Thickness: 1,2mmTop/Bottom Thickness: 0.8mmInfill Density: 30-40% (That it doesn't warp due to the heat of the...

Specifically during retraction and de-retaction, resulting in blobing and stringing. I have modified the gantry back plates by extending the hotend mount by 1.25mm to better align the filament path an hopefully resolve this issue. This may cause the...

**On the Fysetc Spider board, the probing voltage needs to be jumpered to 5V instead of the default 24V that is used for inductive probe.** ## Printer.cfg My probe section in klipper printer.cfg is as follows: [probe] pin: ^!PA3 x_offset: 0...

Use this print to find the right balance. Bridging Test: Look for the length that the bridges start to get messy, and then you know how large a part can be without supports. Stringing Test: Relatively straightforward, just adjust your temperature and...

... A spring from a pen (1)</p> <p>Regarding the pen springs, I specifically used some I bought on Ebay (search for "spring spare ball pen part 424"). They would be the type used for a retractable ball point pen. Category: Electronics

The AMS will detect a problem and automatically retract the filament once it notices it hasn't reached the extruder. If left unattended it might try a few times but will eventually pause and wait for help.</p><p>The coupler inside diameter narrows...

avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 0 default_acceleration = 0 external_perimeter_speed = 70% external_perimeters_first = 0...

Note: This obviously involves the expert view of settings, so make sure it is enabled (since you are about to become an expert!)Under Printer Settings change the following:General/Capabilities/Extruders to 5Custom G-code/Tool change G-Code...

This fountain consists of a large elevated basin surrounded by twelve stylized lion sculptures, all carved from marble.MiniWorld3D&nbsp;is excited to bring this model to life as a homage to all the people of Granada.&nbsp;All our models are made from...

It is intended to help work out extrusion retraction issues (zits). The spheroid shape allows start points for the inside and outside perimeters to start at different places. ...You can easily see any problems on the outside, and you can feel them with...

For the grass, we recommend setting retractions on only for crossing perimeters.&nbsp;Do you like the model and don't have a 3D printer? There are lots of people who offer 3D printing services these days. Try searching for someone who offers them in...