retaliator brass breech 3d models

print the thing, glue the left and right pieces in the respective shell sides of the retaliator/recon, put the mag release in the right one, assemble like normal, and it's integrated

The new stock extender is a fresh take on Hobbes32's design, offering an additional 100mm for your Nerf Retaliator and incorporating an extra tactical rail. ...It has been meticulously recreated from the ground up in SketchUp.

A replacement mag release linkage so that the standard Retaliator mag release interfaces with the stock Talon adapter. The Talon adapter needs to be split into two halves and a very small amount of plastic needs to be trimmed out to accommodate...

Important note: This mod will only work in conjunction with the Retaliator barrel attachment and Recon CS-6 barrel attachment on their respective Nerf guns. To ensure proper fitment, carefully sand down the two nubs (indicated in the image) until...

A stock with thumb hole extention and clip holder. ... Based on https://www.thingiverse.com/thing:3524130 design. But I shorten and reworked it for a better fit / match the Retaliator. ... The clip holder can loaded with darts while it is in the stock.

This shotgun Kit is for Nerf Retaliator You will need Two 1 inch PVC pipe, with the length of your desire. The one I used in the photo is 30 cm for top barrel, and 33 cm for the bottom. paint it with black mate spray paint. ... If you have any...

Expanded Plunger Tube (EXPT) supports for Nerf Recon and Retaliator Models provide a stable base to keep your EXPT in position while supporting the shell from cracking due to stress. It's essential to pad the inside of the tube to dampen impact.

This is a custom grip upgrade for the Nerf Elite Retaliator, utilizing 6-32 x 1/2 screws. The design provides an extremely comfortable hold, allowing for effortless customization and installation. Its rock-solid construction ensures durability and...

This bolt attachment secures onto the receiver of a recon/retaliator, enabling a scope to be mounted directly above, while still allowing for effortless priming without risking damage to the scope. ...I incorporated an auxiliary side dart holder and a...

replaces stock retaliator sight to make front sight look more like scar-L used in conjuncture with SCAR rear sight nerf by 68duck https://www.thingiverse.com/thing:5652882 This object was made in Tinkercad. ...Edit it online...

This new stock extender for your Nerf Retaliator increases length by 100mm, featuring a tactical rail as well. The updated design is divided into two sections with alignment tabs and #4 screw holes for easy assembly. ...The concept originates from the...

An orbiter 1.5 housing I modified to have the breech much closer to the wheel for improved flexible filaments performance

The QB78/79 breech can be elevated using this riser block, which lifts it out of the airtube. ...The riser's height is customizable via the provided SCAD.

An orbiter 1.5 housing I modified to have the breech much closer to the wheel for improved flexible filaments performance

The telescoping breech in the Stryker can slip forward and 'blow out' the air seal if the blaster is modded for higher pressure -tighter o-rings, barrel, etc. This guard prevents that issue. ...(not needed on a stock blaster) -also backwards compatible...

The telescoping breech in the Stryker can slip forward and 'blow out' the air seal if the blaster is modded for higher pressure -tighter o-rings, barrel, etc. This guard prevents that issue. ... (not needed on a stock blaster) -also backwards...

Based upon my previous design, this stock extender will add 100mm to your Nerf Retaliator, as well as a simple tactical rail. The design is now split in half and includes alignment tabs and screw holes that will fit a #4 screw.</p> <p>Both versions...

This is a design for a breech riser that fits standard steel breeches, requiring only a longer hammer pin, dremel bits of exact diameter, vinyl tubing for the TF port, and an m3 thread screw. To prevent the bolt from obstructing it, machine and...

This is a breech riser that should fit the common steel breech, you will need a longer hammer pin(use old dremel bits they are the exact diameter, TF port(Use Vinyl tubing for the TF port.), and breech screw (I would recommend tapping the main tube...

You're about to acquire all the printed components necessary to transform your Recon/Retaliator into a Flywheel Masterpiece! Download the PDF document featuring printing recommendations and non-printed parts list. Acquire flywheels from...

... nice looking rear iron sight. It fits any nerf gun with a rail on it but the iron sight on it only lines up with the flip up front sight on the retaliator. Printed right side up with supports. ...Has my initals on it remove them in CAD if you like.

This custom stock extension perfectly complements the Nerf Retaliator, extending its length by a substantial 100mm while also incorporating a practical tactical rail for added versatility. The design is cleverly divided into two distinct sections,...

This is a replacement piston for the air chamber of an NERF N-Strike Elite Retaliator. The original one (displayed in the photo) failed at the gasket. The replacement part fits perfectly and the NERF gun operates as expected, although the slider...

Based upon Hobbes32's original design, but recreated from scratch, this stock extender will add 100mm to your Nerf Retaliator, as well as an extra tactical rail. Print instructionsPrint with the narrow end down, using 0.2 mm layers and supports on...

I've made significant upgrades to my retaliator stock conversion into a battery box, primarily focusing on refining tolerances to achieve optimal performance. This updated version now includes an optional 35mm extension, allowing for greater...

This 3D model was originally created with Sketchup 8 and then converted to all other 3D formats. ...Native format is .skp 3dsmax scene is 3ds Max 2016 version, rendered with Vray 3.00 european breech (fagus sylvatica) . ...Max hight 45m.

I break my case ejector for my Lee Breech Pro 4000 and found any here so I design one. It works fine so far for me. ... Comment and redesign appreciated

Storage box for ruger rpr 22lr of the breech that disengages the spring, simple and effective Thanks for posting all make and any feedback is appreciated, ideas for evolutions, improvements...

This product features a Lee breech lock quick change ring Die tread that is designed for a 7/8-14 thread size with an outside thread pitch of 16TPI.

The Breech Lock on the Tomcat has some play to itwhich can allow gas to leak if wiggled the wrong way.This shim tightens up the lock. Glue In place.precision matters! ...do a fit check and test first.