replacement parts for glass top patio table 3d models
3318351 3d models found related to replacement parts for glass top patio table.thingiverse
This bracket serves a crucial function as it attaches to the end of a patio table leg, supporting both the glass table and a metal rim encircling the edge of the glass table. Please note that some adjustments may be necessary, as I have yet to...
cults3d
These are the clips that slide into the inside edges of the C-channel rim on a glass top patio table, supporting the glass itself. Clips with an "H" pattern on their backside are intended for use on the sides, while the "Leg End" pieces should be...
thingiverse
These are the clips that slide into the inside edges of a glass top patio table's C-channel rim and support the glass. The pieces with an "H" pattern on the back are designed for the sides, while the "Leg End" pieces should slide over the end of the...
thingiverse
I recently observed that the plastic supports securing the glass surface of my outdoor patio table were cracking and dislodging from their moorings. I salvaged one of these broken components, took precise measurements, and made educated estimates...
prusaprinters
I noticed that the plastic supports holding the glass surface of my patio table have been breaking and falling off. I took one of the broken ones, made some measurements with some guesses as to the screw hole size and center location, and printed...
thingiverse
I decided to re-paint my ~20 year old aluminum glass-topped patio table. When I was removing the glass, the plastic (or maybe some sort of resin) supports holding the glass table top in from the bottom were all yellowed and most disintegrated or...
thingiverse
A replacement spacer/clip is needed for the worn-out ones under my outdoor dining table, which had started to deteriorate due to age. The clips fit snugly into a metal ring and serve as spacers, holding the glass firmly against the top edge of the...
thingiverse
Replacement Clip for Glass Patio Table. ...Designed Specifically to Replace Damaged Parts on Patio Furniture.
thingiverse
My Auntie needed a new plastic ring to go between her patio table umbrella and her patio table, it's a nice easy fit--if perhaps a bit overkill for the task! Umbrella Pole Dia: 1.5in ø || 38.1mm ø Table Hole Dia: 2.25in ø || 57.15mm ø Enjoy. ... ...
prusaprinters
Needed a new insert for my glass patio table to fit my new, 32mm diameter umbrella pole. I resized the model that I found on thingiverse so that it would fit both the 32mm pole and the 50mm hole in my glass table top. The threads...
thingiverse
This is a connnector for a glass topped patio table with rounded rectangle hollow metal legs. Made these as I needed a replacement for a diy refurbishment on my patio table and couldn't find spares to buy online. I'd recommend printing in PETG or...
thingiverse
I designed a custom grommet to fit a 50mm wide hole with a thickness of 5.1mm, replacing one on my table that had snapped tabs due to broken locking mechanisms. Since no replacement parts were available, I created a better alternative myself. The top...
thingiverse
The design's structural parts rely heavily on those plastic elements to support the entire table and glass. After several seasons, the molded plastic began to crack and lose its strength rapidly. I initially designed something similar to the...
grabcad
A corner piece for a rectangular patio glass table is available as a DIY project, which can be printed using a 3D printer from the provided STL file.
prusaprinters
Small Cup Square base to round top. designed for Vase Mode.
thingiverse
Replacement grommet for the umbrella hole of a glass outdoor table. Must be printed in a flexible filament. Print shown was printed in TPU. Glass thickness is 5 mm, and the glass hole diameter is 50.4 mm. The grommet's umbrella hole diameter is 40...
thingiverse
You also need: - 2 18650 cells - Hilumin stripe for welding 18650 cells (eg:...
thingiverse
The sliding parts fit tables like the one shown with a round or octagonal leg OD of 20mm(the hole in my bracket is 20.4mm). The feet will only fit the octagonal profile. Print with 100% infill No Supports needed 0.2mm/Layer I used PLA+...
thingiverse
... with the triangular ribs on the bed, and the feet..... well, foot down! Happy printing! If these are useful for you, and you can spare some £$, I like coffee, you know what to do :) If you can't spare the £$, I hope they're useful for you anyway.
thingiverse
Replacement wheels for outdoor patio heater are needed. These wheels have an outer diameter of 56mm (2 1/4") and an inner diameter of 9mm (3/8"). I designed them with a thickness of 1.2mm on the top, bottom, and sides, used 12% infill material, and...
grabcad
An innovative idea for a table featuring a transparent glass surface serves as its top.
sketchfab
Elegant Console Table with Transparent Glass Top and Sleek Metal Base
grabcad
In 2016's Solidworks, a virtual design was created featuring a table with a glass-top. ...Upon completion of this model, the 3D version will be uploaded, just as done for previous projects which include various bedroom items and staircases.
thingiverse
We scored a sweet deal on a glass-topped table, but it came with one major flaw - several of the rubber pads that protect the glass had gone missing. To solve this problem, I whipped out my trusty Tinkercad and modeled a replacement set. Thanks to...
grabcad
This dining table features a sleek glass top and sturdy cast iron hardware, boasting 8x8 rustic legs that add an authentic touch to its design.
thingiverse
I'm making a glass table corner holder for my parents' wood table, which they've had for years. It's made with rounded edges and is designed specifically for 5.7mm thick glass. I've found that using .1mm layer height reduces stringing and produces...
grabcad
A table featuring a globe crafted from frosted glass as its surface. ...Kindly show your appreciation by clicking the "Like" button.