replacement part for Samsonite suitcase handle 3d models

I designed this handle to replace the original part that breaks often and is pretty expensive. Printing Sliced in Cura. I used Super Quality with 80% infill and printed at 200°. I used PLA. The piece is sturdy. I used raft because I like the look...

This is a replacement handle for Lee's APP Press. It is designed to accept 2 608 bearing, one at each end. It is attached to the press using 5/16 bolt (or 8 mm). Once old handle is removed you will need to drill old bolt hole to accept new 5/16...

<p>This gave a second life to an otherwise perfectly good trousers clamp. ...For the hook I repurposed the wire of a hopelessly bent cheap clothes hanger.The model comes with the FreeCAD file to easily adapt it to clamps with different geometry.

So far no yielding or softening! A replacement handle for the moka pot of some friends. Printed in PETG. Plus: The button of the cap to fit the handle. Print instructionsPrint lying on the side with support activated for the strongest print. Use PLA...

Hello makers... ... Built a replacement myself, after mine snapped (as they often do), the handle diameter is 25mm Updated to V2, as the first one turned out poorly... ... Printed at High Speed 0.3, with 75% infill, no supports were necessary

The original grip on the telescoping carrier snapped off, prompting an approximate redo to restore its complete functionality. ...To function properly, you'll need the original button and retaining plate intact.

... grip piece. I printed it in PLA, but you can also print it in elastic materials to get a more comfortable grip. Printer settings: Material: PLA Resolution: 0.2mm Wall thickness: 1.2mm Infill: 20-30% Support: no Category: Replacement Parts

Replacement part for suitcase "Easylife" ################### After air travel, breakage of one foot on my suitcase handle. Retro design under FreeCAD. ...I replaced the rivets with M3 screws.

... I'll get that done. For best results, print in polycarbonate, heat the tang of the utensil with a propane/butane torch then melt the handle all the way in. ...The polycarbonate will quickly set and won't have the tang go in further than desired.

If you have something quite off and want me to edit the size of the hole, just comment and I'll get that done. For best results, print in polycarbonate, heat the tang of the utensil with a propane/butane torch then melt the handle all the way in. ...The...

This handle button replacement is for "Skara Wheel" suitcases, comprising two glueable parts. Increase the notch size for easier insertion of the other part; otherwise, a Dremel or similar tool may be needed post-printing. ...Designed using FreeCAD and...

Print and assembly instructionsPrint in PETG for durability. ...Afterwards glue together and use M3 self-tapping screws for extra reinforcement.Don't forget to put it on the turning rod first.

A custom grip for IKEA storage containers is being put through its paces to verify thread strength.

Here's an interesting perspective on "just a test fitting." Maybe "fitting perfectly for only one" would give new meaning to that expression.

... I decided to print it in PLA, but you could also opt for elastic materials to give your side cutter a more secure hold.\r\n\r\n_Printer settings:_\r\nMaterial: PLA\r\nResolution: 0.2mm\r\nWall thickness: 1.2mm\r\nInfill: 20-30%\r\nSupport: no

Replacement for a Traveler's Club suitcase handle. Uses original hardware. Slightly narrower than the original but it works. There are 2 versions of the handle: V1 is what I used, it doesn't go deep enough in the telescoping part and the lip...

This is a part that broke on my fridge.

The suitcase handle has been completely overhauled from its initial broken state.

Slightly narrower than the original but it works. There are 2 versions of the handle: V1 is what I used, it doesn't go deep enough in the telescoping part and the lip didn't work right for me. V2 is untested but should go deep enough and has a second...

I need a replacement button for my suitcase right away. Unfortunately, the factory-made one cracked at the hole. Can you please print a new one out of ABS plastic? ...That would be super helpful.

Replacement part for suitcase "Easylife" ################### Air freight, broke one of the feet on my suitcase. Retro design under freecad. ... I replaced the rivets with M3 screws.

Replacement for 70mm tall leg and wheel part, with 60mm wheel diameter.See hardware-recess.scad for the import of recess for M3 and M5 bolts and nuts – https://github.com/avolkov/openscad-designs/blob/master/libs/hardware-recess.scad&nbsp;See...

A sparepart for a suitcase that had a foot missing. ...Since the screw holes are more or less random from factory, I added an STL file med more holes.

The VW Armrest Handle Lock replacement part, specifically designed for vehicles like the POLO, VENTO, and their identical models, has been painstakingly crafted with incredible accuracy - a remarkable 90% match to the original part. Using advanced 3D...

Wittchen suitcase handle repair kit.You need extra:M3x25 screw - 2pcsM3 screw washer - 2pcsM3 nut - 2pcs

... is the replacement! Print it at 100% infill for maximum stability. Unscrew the handle, replace the internal push button with the new printed one. Should fit and work perfectly! ...Printed mine with a Anycubic Chiron with 0,1mm layer height

A few days back our washing machine door handle snapped off. ...So we printed a replacement part that worked astonishingly well. We decided to share it with you all. ... We used an Anycubic i3 Mega (2mm nozzle, 60mm/s speed, 25% infill).

I tried something today- adding a head on top of the replacement handle- i originally made- for that I dled a t. rex- dino stl from thingiverse- https://www.thingiverse.com/thing:613445 to get it done I used freecad- in part wb I transformed the mesh...

I tried something today- adding a head on top of the replacement handle- i originally made- for that I dled a t. rex- dino stl from thingiverse- https://www.thingiverse.com/thing:613445 to get it done I used freecad- in part wb I transformed the mesh...

I tried something today- adding a head on top of the replacement handle- i originally made- for that I dled a t. rex- dino stl from thingiverse- https://www.thingiverse.com/thing:613445 to get it done I used freecad- in part wb I transformed the mesh...