replacement cap and spigot for reliance aqua tainer water jug by 3d models

The end cap is printed flawlessly. ...The ball-valve spigot functions as expected and prints successfully without requiring any form of support material, however it does experience a leak issue.

The spout on Reliance water jugs is infamous for not sealing properly, and/or cracking due to over-tightening caused by a poor alignment of the spout. This gasket functions as both a seal and a cushion, allowing for additional rotation of the spout...

I designed a replacement plug for my broken Reliance Aqua Tainer blue jugs after snapping the spigot off one of them. Created in Fusion 360, printing this design on my printer takes roughly 45 minutes. ...When installing the new plug, make sure to apply...

The cover closes the inside of the faucet to avoid dirt getting into the faucet. ...It sits tight and is hard to pull out, but unscrewing the faucet is easy and will get rid of it.

This is a vent cap replacement for a Reliance Products Aqua-Tainer 7 Gallon Rigid Water Container. I measured off an existing cap and printed in polycarbonate. It requires a rubber insert in the end to create a water tight seal. ...

This is a replacement vent cap for Reliance Products Aqua-Tainer 7 Gallon Rigid Water Container. It was modeled off the original with some modifications to improve printability. I printed using Prusament Polycarbonate Blend Natural color. ... It...

This is an adapter to fit a cheap pump from Amazon ($10) onto a Reliance Aqua Tainer water jug. It is a snug fit for my pump and the thread works great (kudos to the great thread library at https://github.com/adrianschlatter/threadlib/ ). I hope...

The jug is called the Aqua-tainer https://relianceoutdoors.com/products/aqua-tainer-4g-15lI pillaged a few STLs on the ‘verse and two worked out for me I can’t seem to find them now, however. This replaces the spigot and utilizes the OEM cap. My...

This is an adapter for the Aqua-Tainer water jugs sold by REI. These use a difficult to find M25 fitting. This adapter provides an M25 Male on one end and a Male Garden Hose Thread on the other, allowing the jug to be used for pouring into another...

-- The protrusions on either side of the centerpiece enable fitment of the spout to the lid when in use, and help seat the gasket for a watertight seal when it is closed.I also lost the vent plug and found a replacement part from...

This is a WIP. ...It is meant to fit onto the spigot, of a "camping water jug", and create a 1/8" hole.

Could not find a cap and spigot for my 10l nutrient container so I made one. !!!Print item 103% larger than file to fit on bottle!!! Spigot that goes into hole is from here ~ https://torontobrewing.ca/products/spigot-1 Spigot needs to be 1"...

I misplaced one of the caps for my five-gallon jerry can-style water jug, so I fired up Fusion 360 and copied the original design to print a brand-new cap. ...This cap fits perfectly on my water jug, which you can find here: http://amzn.to/2aqXeP2 I...

This is a generic cover to go over the Spigot of a water fountain in order to prevent someone from drinking from it.It can be printed with no supports (opening down), and secured to the Spigot with a zip tie.

This is a generic cover to go over the Spigot of a water fountain in order to prevent someone from drinking from it.It can be printed with no supports (opening down), and secured to the Spigot with a zip tie.

This is a generic cover to go over the Spigot of a water fountain in order to prevent someone from drinking from it. ... It can be printed with no supports (opening down), and secured to the Spigot with a zip tie.

I created this spigot file to replaced my broken spigot on my Water jug. When the print is complete, it will look bigger than the original one. ... I hope you find this file worthy as much as I have; especially when I was not able to find a new spigot...

Attaches to a the spigot of a 7 gallon reliance jug so you can fill water bottles with a smaller opening and not dump half the water on the ground. Printed in TPU. ... Snaps on to the small ring around the edge of the stock spigot

I bought a nice military grade Scepter water jug this last summer for a trip I went on and the jug is fantastic, it very durable and pours really well with a regular spout and a vent. However, the cap that goes over the main spout has a little strap...

Needed a replacement cap for an igloo jug (~5.5" dia, ~12" total height), so I designed this in Tinkercad. Printed in TPU with 10% infill, but decided to reprint with 50% as it will see heavy use. Both printed fine on my Ankermake M5. Used...

Designed a kit to run a cheap water pump off Amazon to bring water out of my 7 gallon water tank. ...This adapter allows you to replace the spout with a hole for a hose.

I made this top part of a tap for a broken glass water dispenserUse the function in your slicer to lay the part down on it's flat side.Washer is used on a nail or pin (ø1.75mm).

Brought some Ozark 5 gallon water jugs for scouts and one was missing a cap...quick design.

Elements of the _Exit Aqua Flow_ water way are stacked using a cylindrical wooden pillar that screws in under each element of the way. These tend to rot, as they are in the shade and exposed to humidity. This piece is a replacement for these wooden...

Remixed to fit the pictured cap. ...I don't have that cap, so please tell me how it goes. You should be able to scale it in your slicer to make it fit. If you do, tell me you scaling adjustments and I'll fix the model. ... Cheers!

Remixed to fit the pictured cap. ...I don't have that cap, so please tell me how it goes. You should be able to scale it in your slicer to make it fit. If you do, tell me you scaling adjustments and I'll fix the model. ... Cheers!

I designed a part that replaces the connector between the spigot valve handle and plunger. I needed one after my original broke off, so I created this to fill the gap. It prints well on a raft and functions perfectly. ...Initially, I printed it with...

Standard Bubbler Airlock Cap for Cider Production Requires Specific Equipment and Printing Techniques. Ciders can benefit greatly from using a standard 5-gallon water jug equipped with a 7mm hose bubbler to achieve precise fermentation control. To...

This is a screw-on cap designed specifically for 5-gallon water jugs with a pre-drilled hole, allowing a 5/16-inch sap line to connect directly into the cap for efficient maple sap collection. These caps work exceptionally well at keeping rainwater...

I lost my spigot key so I designed this. ...Spigot keyhole is 16 mm, square metal part inside keyhole is 8 mm to a side. ... Swedish description: Nyckel till vattenutkastare (sökord: nyckel till trädgårdsslang)