remote holder for chair 3d models

Built in cable-ways for remotes with cables (for chair reclining and massage controllers). I have included the Fusion360 file to modify for different chair dimensions. Gcode file is for PLA @215C, .6mm nozzle, snug supports and .35mm layer height for...

This is a holder for up to 3 remote controls & can be hooked over the arm of a chair or couch. I designed it for a square-top arm of 6.5 inch (165mm) width. It prints in 4 pieces: the arm hook, remote pocket, & 2 retaining pins. I use it to...

Remote control for easy adjustment of the inclination of a chair in any position

This thing was created with Tinkercad. ...Edit it online at https://v1.tinkercad.com/things/e3k5VLURBY3. It features mounting hardware on the back for easy attachment via screws or double-sided tape to a wall or the side of a chair.

This is a holder for the remote control for the radio in my Geo Pro G20BHS travel trailer camper. It mounts with 3 #4 screws. The fit is somewhat snug, hopefully the romote won't fall out while driving down the road. My prototype was printed...

Cheap eBay Remote Owner Here. ...Using the remote to control multiple lamps is easy and convenient.

Designed in Tinker CAD to hold a LED remote control.

 I used four chains altogether in the fabric chair shown in the photos.One of the three prints provides two five-link chains.  You will likely need to print these a couple of times to get the chains of sufficient length. ... The chain...

Remote Control Holder Device to Carry a Remote Control

Holder for 3 Remote Controllers, 2 small and 2 bigger remotes (Chromecast wiuth Google TV, AC unit and TV/Receiver):)

Hi! ... I always have remote controls scattered around the apartment. And I decided to make a holder for them, which is screwed to the table from the bottom, so that the remotes are always in their place.

Place holder for VELUX remote Attached to the wall near your light switch cover, this holder is conveniently placed. Simple directions 1. Find the ideal spot between the wall and your light switch cover. 2. Secure the holder in position. 3. ...Enjoy...

Device Holding Mechanism for Remotely Controlled Apparatus.

... attaches easily with double-sided tape or glue, while the other requires just two simple 4mm wood screws. The holder designed specifically for Fire TV remotes was created by osulivan and can be found at: https://www.thingiverse.com/thing:1339490

... to just have the remotes for TV and FireTV in reach. ...This holder hangs on the drawer og the Hemnes (or any other drawer really) and fits two remotes easily. ...You can even hang it over the drawer knob if you have a symmetrical fetish.&nbsp;</p>

My wife requested a TV remote holder, so I built it.

I printed this with PETG no support needed tested and fits in: Ford Mondeo 2012, Fiat Tipo 2020 the holder is for the RMCTR remote from Giant (sold on aliexpress, alibaba, ...)

There are numerous remote holders available, however most of them require mounting on walls or similar structures. This one is designed to hang right off the edge of your bed. It will hold a remote with a width of about 55 mm (~2"), thickness of 30...

A simple two-part holder for a remote control with a width of 22 millimeters is all that's needed. I used the TESA PowerStrip to secure it firmly on the backside of the TV, where it will stay put. The adjustable length allows it to fit any setup...

This Remote was specifically designed to be mounted underneath or side of a coffee table using doublesided tape or glue, depending if it is permanent or not.It is designed to be a bit loose so that the remote can easily slide in and out of the...

Enjoy :D!Print instructionsCategory: 3D Printing SummaryA holder for a 5 plug ZAP remote. On the back, there is a 1-inch wide indent for some double-sided tape. ...Enjoy :D!</p><p>Edit 3/6/2022: Added version without recess.</p><h3>Print...

Remote Control Handrest

The Case File: Mysterious Remote Control Enigma

A convenient carrier for your 5-socket ZAP remote control is here. ...On its reverse side, a small recess, measuring one inch in width, awaits a strip of adhesive-backed tape to secure it firmly in place.

... I need both hands free for something like changing eyepieces. ...The simple solution lies in attaching the remote control clip to one tripod leg, which not only keeps the device at hand, but can be easily transferred to any other leg of the support.

The tiny print has been added to the screen.\r\nA compartment specifically designed to hold the remote control is now available.

Its a remix to fix it on a wall for example.

... a Nozzle size of 1.0 and Layer Height set at 0.3. ...To achieve even higher print quality, you can reduce the Layer Height further, but I opted for speed instead, preferring not to wait any longer. ... Print Settings were as follows: Printer - Anet A6

Remote Holder for 9 RemotesFernbedienungshalter für 9 Fernbedienungen

Needed a holder for my remote that controls my HDMI Matrix. ...Designed in Fusion 360