remo hobby 3d models

spur for remo hobby smax 39T

It's a remix of the Remo Hobby SMAX arm r1631 by Yurecbts, but I've made it even stronger and more suitable for printing. I highly recommend using PETG with 100% infill to get the best results. ... This version is designed specifically for the Remo...

This is part No P2506 for Remo Hobby Smax. ...I optimized it for 3D printing.

This is Part Number P2506 for the Remo Hobby Smax, specifically designed and optimized for use in 3D printing processes.

Towers of Remo Hobby's sleek design are replicated to perfection in these 1/16 scale models, crafted from the durable yet pliable PETG filament.

2.STL is made with slots, so if your plastic is fragile, try this one.Верхняя крышка для штатного пульта дистанционного управления Remo Hobby. Есть 2 версии: 1.STL без прорезей. 2.STL имеет прорези, поэтому, если у вас хрупкий пластик, попробуйте эту...

The Remo Hobby Smax (RM1631) is designed with safety in mind, featuring a durable battery compartment and protective casing to prevent damage from rough handling or crashes. The high-quality electronics ensure reliable performance, while the...

Here is the bumper mount for the Remo Hobby Crawler. I Printed it in PLA because that's all I have. I went with 100% infill to stiffen it up. I printed it on it's side and used Prusa to build supports and slice. V2 update has been strengthened. ...

Humans often seek stimulation through remote hobbies such as extreme sports.

This battery cover for remote controller Remo Hobby

Средняя часть диска (самая ломающаяся) RC модели 1:16 S-Max от Remo hobby. ...Немного усилил.

Waterproof box (Remo Hobby/Traxxas Slash) Print Settings Printer Brand: Prusa Printer: Prusa Steel Rafts: Off Supports: None Resolution: 200 microns Infill: 100% dense

доработал колесо для дрифта на машину Remo Hobby 1/16 то что нашел на в интернете задевало за переднюю ступицу, пришлось изменить колесо путем вырезания внутренней части обода. ...печатать можно хоть ПЕТГ хоть ТПУ.

This is a game-changer for the Short Course Remo Hobby 1/16, making it a full-fledged vehicle rather than just a spare tire.\r\n\r\nHold the parts together with super glue.

This is a replacement drive shaft for Remo Hobby Smax 1631. Old one was broken during a stunt. Fits perfectly into the housing. Maybe print in PETG or ABS if possible for better durability, i will also try later on. I printed with brim 1mm and...

If you want to modify your Remo Hobby SMax or S-Evor or short-cross to Dingo (baggy) edition, you will meet a problem with fixing front side of Dingo body shell. My model will help you with it. Use two existing screws and new one for fixing the...

This reinforced suspension arm (part number P2505) is designed for Remo Hobby SMax 1631 or 1635 models. The original detail's print usually breaks after the first strong hit, but this reinforced version can withstand much more impact. To assemble it,...

Arm for Remo Hobbes Smax 1631

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Original version has too thin borders and got cracked in half in first 30 minutes of ride. Two new versions - one is fuly filled, another with some holes. ... Recommended fill - 50%, concentric pattern for top/bottom.

Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.

Spur

Wheel for RC car Remo Hobby 1:16 !

A lower shock absorber part for my Remo Hobby M-Max. ... Will probably fit other Remo Hobby RC-Cars.

Support for Wltoys 144001 Remo hobby hobby body shell D2602/D2603/D2601 Front and rear support.

Rear body post for Remo Hobby Trial Rigs Truck 1/10. ...5,5 mm diameter.

rear suspension mount without gearbox cover traxxas slash 4wd remo hobby 9emu

This is a RC car LED lights for HSP Brontosaurus and Remo hobby SMax. Outer diameter is 14mm. Mounting bracket hole is 5.6mm for HSP and 3.7mm for Remo. LED size is 5mm. You can use two options: to glue mounting bracket with epoxy or to glue it...

If you own a Remo hobby 1073 Trial RIgs truck you probably know it has a weak and brittle Lexan part of the body. Should you find an original SCX10 Honcho cab, you can mount it using these stands. You will need to move rear shock mounts by one...

I made my own spare parts for 1/8 scale Remo Hobby EVO-R truggy. When I lost drive on one of the wheels I found hex rounded. As aluminum as in rim hub. I made two versions of hex drive (standard size and reinforced), and new hub for rim. When...