remake 3d model

I used this 5/8" tall flat bellows available from McMaster Carr:https://www.mcmaster.com/1320K111/These bellows are made for this job and are resistant to oils, lubricants, and heat.The models are designed to fit an Eerie Tools SM-LTHM 7x14 lathe but...

Also, no screws or other fixing methods are used. How it works can be seen in the video UPD I added a version in two sides in the form of frames, its printing a third faster and when printing a model, corners closed by cooling by a fan are not...

Basic overview:This is a drop in replacement barrel for the Dart Zone Solo Pro that is designed to allow it to fire mega darts, but I designed the model in a way that it can not only also still fire half darts, but fire rival ammo too! It shoots Mega...

... self sustaining for long periods. All ground piping, cabling and the Large Gas collection cansiters would be covered in Dirt once operational for Sun / wind shielding. Note the Space Suit man was inserted for size, got it from the NASA models site

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

2022-04-14 I started to create a new base that could use threaded inserts and quickly realised the base models had become quite complicated due to the iterative design process, so I went back to basics and recreated them. The new housing mechanism is...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

  ENGLISH-------------Only tested on T12-X, but can work on equivalent models with boxes of the same dimensionsI found my T12-X soldering station a little too bulky, the screen not very visible and too dark. I also wanted to have all the...

Every link piece adds roughly 2,5 cm or 1 inch. Step eight:Cut Filament to 2,3 cm and attach the body strap to Piece K connector strap. Step nine:Cut again Filament to 2,3 cm and attach the N handles to M handle attachment:Congratulation, you just...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

*Download new version 1.01 here: https://www.printables.com/model/178925-ender-3-s1-stealth-light-bar-easy-to-print-and-do-mod ( Maintaining on Printables ) Easy to print light bar that uses the built in accessory port for power. This allows for...

Every link piece adds roughly 2,5 cm or 1 inch. Step eight:Cut Filament to 2,3 cm and attach the body strap to Piece K connector strap. Step nine:Cut again Filament to 2,3 cm and attach the N handles to M handle attachment:Congratulation, you just...

A custom-made enclosure specifically designed for the Raspberry Pi computer assistant Assistant assistant A bespoke casing tailored to fit the Raspberry Pi device. assistant Created especially for the Raspberry Pi, this is a one-of-a-kind case. ...

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

If you want it with an internal battery, I have designed this same model with a hole for the battery, measuring 126x85x35mm, you have it here: https://www.thingiverse.com/thing:6016217 Required Components: - 1u Mini ZVS Module 5-12v (...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

I just have to choose a bulb of the wattage I want and with a high CRI to get the best image quality.Since Fresnel spotlights are a classic in the world of cinema, I based my project on a model of the Arri brand from the 1940s. Which has a spindle as...

Remember to check the wiring of your relay if you use a different model or brand. Adjustments If you set the microswitch to click when the bed is at Y=220, then it will work out of the box with Cura. I still recommend you to modify you G-code to...

The files under Skycat17 (this one and a model of the Chrysler Building) are still available for download on Thingiverse. But I have no access to even see how many have downloaded or responded. The Tripod. The Phone Holder. All 3...

And Happy Printing!-------------------------------------------------Originally designed in Fusion 360 and printed with Prusa Mini+ THIS MODEL IS UNDER CC (Creative Commons) LICENCE. Note: The DO NOT EAT sign might not print properly due to...

The COMPLETE Order of the Labyrinth bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The strong Minocs of the Order of the Labyrinth are the descendants of Tesevros the Wise,...

Deck furniture is always a good way to add interest to a model. You might want to install a waterproof switch somewhere on the exterior to save having to unscrew the whole deck every time to turn it off and on. Enjoy sailing your Pocket Boat,...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

Do not purchase unless spare parts are easy to get; not all parts are easy to CAD model or print. OEM replacement parts for the q905 can be found [here](https://www.hosim.com/collections/parts-for-q903).You can also take the OEM part number and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...