reloading annealer 3d models

Customized version of http://www.thingiverse.com/thing:260104 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Instructions Using the following options height = 19 diameter = 15.65 number_of_rows = 5 padding =...

Created a Lee Die Spanner for tightening of Lee dies. ...

Customized Version of http://www.thingiverse.com/thing:260104 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Instructions Building with these options: Diameter: Set at 11.4 units ...

Loading the die holder into position on a typical wooden rack is straightforward and effortless.

A Grid of Identical Rings is being custom made for you based on a popular design found on http://www.thingiverse.com/thing:260104 using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=260104. ... Using the...

Customized version of http://www.thingiverse.com/thing:260104 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Using the following options: height is set at 20 diameter is fixed at 15.6...

Here is a customized version of the Thingiverse design: http://www.thingiverse.com/thing:1457037 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1457037 Instructions...

Hello everybody, I'm excited to share my first design on Thingiverse. This custom holder is designed and crafted to securely store shell holders of various calibres. Below, you can easily write or attach a label for each caliber. ...You'll find two...

I wanted a better way to organize my dies, so I designed a pegboard mount to hold them. These were designed for Hornady dies, they may work for other brands. Use supports for the rear peg hooks, 15% infill, eSun PLA+. I have versions with and...

Customized version of https://www.thingiverse.com/thing:1457037 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1457037

Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=260104 Instructions Using the following settings: column_amounts = 10 edge_thickness = 2.432 inner_diameter = 9.408 number_of_sections = 5...

Customized version of http://www.thingiverse.com/thing:260104 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Instructions Using the following options: number_of_columns = 5 height = 9 ...

Spline drive lock nuts - designed for use with Lee spline wrench Locking version requires a #2-56 screw; I've only tested with 1.5mm screws so far. ... If any of my designs prove helpful, a comment is appreciated and tips are always welcome.

Customized version of http://www.thingiverse.com/thing:260104 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Instructions Using the following settings: Diameter is set to 10 units Number of...

Customized version of https://www.thingiverse.com/thing:1457037 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1457037 Instructions Using the following settings: Pad = Zero Convert = inches...

The standard-duty die block is designed to hold dies with 7/8"-14 threads. ...It's suitable for the majority of manufacturers such as RCBS, Lyman, Dillon, LEE, and Redding, among others.

Round capacity increased by hundred percent, a 900-round 9mm ammunition holder

Customized version of https://www.thingiverse.com/thing:1457037 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1457037

Customized version of https://www.thingiverse.com/thing:1457037 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1457037

A simple way to steal the powder out of your powder dispenser while tuning in the correct load etc. no brass needed to be put in and out your press each time you want to weigh the load. I designed this because i wanted to trickle the load in a...

Remix of Reloading Cartridge Trays by Crashin_Machines: 45-70 tray, engineered to accommodate 7.62x53R ammunition seamlessly.

... tray holds 50 rounds. Crafted to fit bullet measurements with precision, making the reloading process smoother than ever. We value your input and want to hear from you! ...If any defects are found, please report them so we can refine this design.

I have a very small space in which I do reloading and I therefor designed the reloading trays to take up minimal desk space and to be stackable when not in use. The spacing between rounds might be a bit tight for some folks... Tray length and...

Spent primer funnel for Lee Breach Lock reloading press. You can hang a bucket on the hook and all primers will drop there. ... Print with basic supports.

I have designed 2 iterations of a 338 Lapua reloading tray. One holds 25 rounds, the other 49 rounds. ... Easy print, no supports needed.

Updated 4/05/2019 - fine-tuned brass pocket for improved powder funnel fit with 38 SPL brass Updated 2/12/2019 - refined brass pocket A reloaders' dream comes alive in this 50 round reloading tray, inspired by the ever-popular Frankford Arsenal...