relief model architecture

Basic overview:This is a drop in replacement barrel for the Dart Zone Solo Pro that is designed to allow it to fire mega darts, but I designed the model in a way that it can not only also still fire half darts, but fire rival ammo too! It shoots Mega...

If you want to be able to focus it, you'll need a helicoid that maintains or falls below M42's register distance of 47.46mm at its shortest for your camera setup. Disclaimer: This model is offered AS-IS with no guarantee that it will print for you as...

Moreover….Sitag astonished me a lot because actually….they continue to make and sell the same model: the famous “Sitag Reality”…which costs now around 700€ !!!Therefore, I decided to try a repair with my engineering skills and a big dose of...

Z gap between support interface and model is 0.2 mm For the adapter plate I used standard supports with the same support options Other parts: For convenience, I included the 40 mm fan cap, part cooling duct and BLTouch mount from the original...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

This seems to be a weak point in all reciprocating saws and is a particular problem with this model, with some users reporting that the blade clamp had sheared off after only relatively light work. Replacement parts are available, but at a...

A big thanks also to Eric Clinedinst who helped me to find the first issue. This is the BOM list for the internal part: 1x 5x10x4 (MR105z) Bearing for indirect filament sensor 1x round neodymium 8x3...

I have re-modeled them a bit and now there are only a few strings. None if you print them with a 0.12 layer height. Filament Dry Box Set (Updated 3/11/2021) This set of prints are designed for use with the following items to create a very slim...

For the launcher and the “motor” (= nozzle and adapter) you can find additional info here: https://www.printables.com/model/46571-water-rocket-and-launcher-platform-complete-instru These parts have been proven to be working (see old video). The...

6) I don't provide holes in the model for the harness or for the charging connector. These are also variable. I happen to use an RCA jack for my charge connection and I just drilled a hole for the silicone insulated wires to exit. 7) I glue the...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

# Supplies you need to buy: 1 Logitech M510 Mouse (this model exactly) https://amz.run/67er 2 Philmore push button switches https://tinyurl.com/mr42ce4n Solder (lead is easier to work with) https://amz.run/67nL Wire https://amz.run/67f4 Super...

Once you have the rights % size change, you can Meshmixer or TinkerCad any model onto the clip_in_insert to create all kinds of new experiences for your animals, or useful things such as a cover for a feeding area to prevent gunk from falling into...

It removed the support, but also broke the model. Before I removed support from the second trolley I drilled out the majority of the support going through the assembly hole with a large drill bit. After drilling, the removal trick on a vise worked...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

So, don't be alarmed if you notice discrepancies.) And another NOTE: If you're looking to upgrade the model cooling blower to a 5015, I have something very similar to the Z-19, but which supports the bigger blower: I called it the "Z-23", and here's...

We also offer other variations of this light if needed to fit your specific application, 120-277V AC, 12-24V DC, and 0-10V dimmable models.Our EPL-24-2L-LED-347V LED light fixture is NRTL Listed for United States and Canada approved for use in paint...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

[Video](https://gitlab.com/jdobry/hevo-mgn/-/blob/v3/DOC/video.md) ============ [](http://www.youtube.com/watch?v=EZKwii39ZXY "Video Title") [![IMAGE ALT...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

I recommend 8 IKEA LADDA AA cells as they are amongst the best available anywhere (https://www.ikea.com/us/en/p/ladda-rechargeable-battery-70303876/):https://cults3d.com/en/3d-model/tool/aa-six-cell-battery-holder The one piece parts need a big...

It has been argued that for the N2+ model with a print that could fill the entire 2 foot tall bed, these springs would compress and the object would then miss layers and ruin the print. If I were worried about printing that tall with that high a...

I was basically trying to address two "issues" of my Anycubic Vyper: - The PSU and Mainboard 24V fans are very loud - I want to upgrade my Vyper with an OctoPrint/OctoPi setup So here is my result: - An upgraded PSU cover featuring a 92mm fan mount...

Your purge block will be rather large, so if you have a suitable item you can use as a wipe model, use it! Then, remove the 8 outer-most parts and core, leaving just the inner 9 components. You will need to reassign colours, i.e. red becomes the...

Summary Section: A partner and I worked together to design a 3D model for a ghost bookmark clip. Based off a doubled-scale diagram of an example bookmark marked up with original dimensions, we created the 2D sketch on the SOLIDWORKS program. We...

This model is intended to be glued together using Gloop! Get your Gloop! here: </strong><a href="https://3dgloop.com/shop"><strong>https://3dgloop.com/shop</strong></a></p><p>Assembly made without using Gloop! may result in the need to prepare for...

The tubes used for processing in the Whirlwind would end up leading Ken Olson to transistors, which led to the transistorized TX-O (the love of many a tech model railroad clubber) and later to Olson founding DEC. Suddenly, the Whirlwind was the...

Also, this particular model has a bunch of different colors to really pick your perfect cart!&nbsp;What You'll Need ExtraParts:4x 14" long, 1" OD PVC pipe [355mm Long, 25mm OD] (theoretically the metric standards available should be identical) Note:...

The attached model is sized to fit the Eye Cu Smile V2 and V1 filter housings at 45 mm OD and 10.5mm high However if you want to make any size antimicrobial / antiviral filter meshes for any purpose then even sketchup will suffice Steps to draw a...

The files are prefixed with Updated_ or New_.Here are a couple videos of it running  Please refer to the Original model for assembly and any other sources.I have uploaded the file as a Fusion 360 archive folder so you will need Fusion 360, Fusion 360...