relic 3d models

This is my design of a toy meant to teach children about the effects of an inclined plane on a rope/pulley system and the forces involved.  There are 4 3D printed parts in total and 7 externally sourced common hardware materials.  OpenSCAD Source...

No short circuits between the V G and/or S wires. Hardware I used these end-stops: https://aliexpress.com/item/32959048821.html I am not affiliated with AliExpress nor TwoTrees and there are LOADS of identical/rebranded switches out there. You will...

You can cut the circle that's sandwich between the two 3D printed pieces with good scissors. The holes for the crews and the tube are harder to make. Be careful, this mesh is sharp and you can get cut. I'M SERIOUS. I managed to make the screw holes...

The information-processing equipment, for its part, will convert hypotheses into testable models and then test the models against data (which the human operator may designate roughly and identify as relevant when the computer presents them for his...

So _1_6_10_7 is 1:600000000 or one in 60 million. The accuracy of the model The model was made taken these features as literal from the book: The spaceship was a cylinder 50km long and 20km in diameter, although it can be expected aliens having...

You don’t want them pulled too tight. Install the Chain Link Cover Clips onto the drag chain links to close the chain. Slide the Cover pieces into place over the Chain Frame Mount and the Drag Chain Arm Connector.Edit 2021/08/07: Added Genius...

As always, the .blend file and pre-supported .obj (the one that I used to print it on my Prusa mk3 with a .25 mm nozzle) for this model are available to my patrons at https://patreon.com/VirtuallyJason. If you appreciate my work and have a few...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Additional mounting types are avaiable for this model.This explosion proof LED light fixture is paint spray booth listed, IP67 rated, dust-proof, and protected against high pressure jets and temporary submersion. The cast aluminum body and LED lamp...

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

The first one was a box, with an RFID reader, that provided clues on its LCD screen and had a secret compartment that opened with a specific secret code. The second device was this Bocca della Verità with RFID in the mouth (it was a secret) provides...

  I also modelled in clips for these PCBs to hold them in place whilst soldering up.I will share my order for my PCBs on jlcpcb so anyone can order once I figure out how :D Tools RequiredSharp knifeLong Nose Pliers Note that the 3mf...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 0 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 stencil_pattern_line_thickness = 30 printer_tolerance = 0.4...

... weapon. By Alex Wellerstein, a historian of science and an assistant professor at the Stevens Institute of Technology, in New Jersey. Attributions: •Screwdriver by user DAPE, Cults3D (under CC-By-Sa-Nc). •Demon Core modeled by Szadros. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

The stock globe has a vent on the top and there are vents in the model to aid the convection cooling. Is it *really* needed, especially with the converter gone? Dunno so the optional rain cap comes with the caveat of possibly shortening diode...

I got a package of 5 and when I opened them I found that the design had changed slightly and the material they used on the newer models was slightly thinner. The original clips were therefore a little sloppy. I adjusted the clips to fit the newer...

UPDATE: 20.04.2022adapterplate (new design) for model C Hello, we would like to introduce you to our stealthburner conversion mod. At this time it works only with the klipper Firmware. The use with “Marlin” is planned later and will be...

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Since the build volume on the Prusas is relatively limited i decided to maximize the footprint of the stand for stability. As for the height, the 2 piece construction while theoretically takes more time to print, there is no need for support for the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

... > No. I planned to use sensorless homing and didn't need it, so I didn't add it. # Misc * [If you are wondering where the beautiful Hemera model in the pictures came from, here is a link ](https://grabcad.com/library/e3d-hermes-hemera-v6-volcano-1)

Printing time is &gt;15min.Credits:The original configurable OpenSCAD model is by wstein, posted here. ...Thank you Werner!</p><p>Thanks to <a href="https://www.printables.com/social/78665-darktiger/about">darktiger </a>for his print and picture of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

Both the original base (Base.stl) and the updated version (Base_Rev.B.stl) are included. 4 (7/15/18): Added versions of the Deer Scarer, Waterfall, and Electronic box with custom supports modeled in. Supports were built based on the method showed by...

... and presupported version. This product contains the following parts: 32mm Base 40mm Base Captain Samira DnD 5E Datasheet Get a 40% discount on this model by joining my Patreon! ... You can also order physical copies at my shop on Only-games!

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...