relay for raspberry pi 3d models

Relay Mount for Raspberry Pi 7" Touchscreen It's a pretty specific use case. It will accept two different relays: 12V 4ch Relay - https://www.amazon.com/dp/B00LW2GM84/ 12V Timer Delay Relay - https://www.ebay.com/itm/122552064797 Used for my OpenAuto...

I'm adding a housing and clip to attach a relay board to my Raspberry Pi sleeve case securely. ...The board is fastened firmly in place using two M3 screws.

This is a custom component designed for seamless integration with the Raspberry Pi. To ensure a secure connection, you'll require four M3 screws. No bolts are necessary to complete the assembly. ...Although the clip is included, its use is optional,...

This case was designed for a 3.3V relay to switch on/off a 3D printer remotely with a Raspberry Pi. It is based on a Chinese relay module available on eBay:2PCS 3V 10A 1 Channel Relay Board Module Optocoupler LED for Arduino ARM AVRThe design...

This case was designed for a 3.3V relay to switch on/off a 3D printer remotely with a Raspberry Pi. It is based on a Chinese relay module available on eBay:2PCS 3V 10A 1 Channel Relay Board Module Optocoupler LED for Arduino ARM AVRThe design...

I require a housing for the Raspberry Pi and relay board with specific additional requirements: 1. Screwless 2. Slot for cable management must be present 3. Minimal use of zip ties is allowed, but not prohibited 4. ...A mount point must be provided to...

Designed this layout for building a 3D printer control box for my Taz 5 SKR 1.4 Turbo upgrade, enabling remote power on/off with Octoprint using this relay to manage the 24v supply to the board. ...The heated bed will be connected directly to a 100A DC...

Designed a functional blueprint for a custom 3D printer control box, enabling seamless remote operation through Octoprint with simple on/off functionality.

I used foam tape to attach it to the power supply on my Ender 3 and Velcro to hold the cover in place, making it easy to access the relay when needed. A ventilated design prevents heat buildup from the relay itself. ...Tabs at each end of the base allow...

You can easily install a 4-channel relay module anywhere.

... 0110-M-P's original model at https://www.thingiverse.com/thing:922740. ... The primary changes made were to house a 4-Channel keyestudio relay board that can be mounted directly on top of a pi. ... The model was printed using a Flashforge Adventurer 3.

... out there on how to wire the GPIO pins on your R-Pi. I used pins 4 and 6 for power and ground, respectively, and pin 40 (GPIO-21) for signal. You'll want to have a decent power supply for your R-Pi to handle this relay. ...I recommend 3 amps.

Modified this to hold a female DC connector as well so I could use it for this project: https://github.com/fmalekpour/OctoPrint-Cooldownfan Modified from: https://www.thingiverse.com/thing:1726120

Little remix (it's redesigned by me for scratch but it's the same thing. ... Its designed for Raspberry Pi 4 with metal case. ...It have support for 1CH relay for power ON/OFF and some drill for cable management.

I designed this specifically to cover three Raspberry Pi at once with the Relay Board used for home automation, for switching on my 3d printer & lights using octopi and for my astronomical observatory. ...Additional details can be found on:...

PSU Plugin: https://plugins.octoprint.org/plugins/psucontrol/ Relay: https://www.amazon.com/Channel-Expansion-Arduino-Optocoupler-Triggered/dp/B07LH53G5F I always keep my Raspberry Pi on, while the relay simply cuts off 220v power entering the...

This is a simple enclosure designed specifically for use with a Raspberry Pi 2 B and a Relay Board, eliminating messy cables from around your 3D printer entirely. I utilize the relay board to switch my printer on or off remotely, which proves to be...

I required a garage door opener as follows: A protective case for a Raspberry Pi Zero W, an SR-HC-04 ultrasound sensor, and a relay. ...The Raspi runs a node.js web server, measures the distance to the garage door edge - whether it's open or closed -...

I designed a mounting bracket for the Raspberry Pi Pico, to mount it onto a 4-Channel relay. The bracket has 3 holes to mount the Pico with M2 bolts. The bolts screw right into the plastic, no threads needed. I use these setup as a simple watering...

I designed a mounting bracket for the Raspberry Pi Pico, to mount it onto a 4-Channel relay. The bracket has 3 holes to mount the Pico with M2 bolts. ...The bolts screw right into the plastic, no threads needed. I use these setup as a simple watering...

The Raspberry and Relay Extension Shield Combine into a Seamless Whole within One Expertly 3D Printed Case. Initial Testing Shows PCBs Fit Perfectly as Captured in Stunning Images. ... By Opting Out on Dedicated Holes for the Camera, GPIO Connector, and...

This is a redesign from https://www.thingiverse.com/thing:4140386 to the Ender 5 Plus, added an option for a larger relay board, A larger Buck Converter and Added a spot for the MKS UPS. To install follow the pictures above I found it easier to...

This is a redesign from https://www.thingiverse.com/thing:4140386 to the Ender-5 Plus, added an option for a larger relay board, A larger Buck Converter and Added a spot for the MKS UPS. To install follow the pictures above I found it easier to...

... In addition, a 4 Channel Relay is also compatible with the Orange Pi 3 and can be stacked on top for convenient access to all your components during installation and configuration, making it easier to disassemble when needed.

Designed a case to hold for X5SA Pro to hold all the new electronics. ...It will work for any 2020 VSLOT. IT enclosure holds - SKR 1.4 Turbo - Raspberry PI - Bigtree Tech 24v UPS - 5V Relay to control power to the card using RPi - Plenty extra space

This custom PSU case for the Ender 3 replaces the stock case and adds a spot to mount a 3v relay, and a separate attached enclosure to mount a Raspberry Pi 3. The enclosure has a lid that slides on and off easily to access the PI. In addition, there...

Very simple snap-together case for Raspberry Pi 3 Model B and Sainsmart 2-channel relay board (https://www.sainsmart.com/products/2-channel-5v-relay-module). Boards are mounted using M2 screws, and a slot allows for wires to connect to the screw...

Very simple snap-together case for Raspberry Pi 3 Model B and Sainsmart 2-channel relay board (https://www.sainsmart.com/products/2-channel-5v-relay-module). Boards are mounted using M2 screws, and a slot allows for wires to connect to the screw...

This design is a remix of my Raspberry Pi 3 Model A+ case for the Raspberry Pi Model B+: It adds a case to your Ender 3 (Pro) that fits a Raspberry Pi 3 Model B+, a 10A relay (for switching LEDs on/off), a 30A relay (for switching printer on/off), a...

Raspberry Pi 3 A+ with 30A relay module case to use with Octoprint and to mount everything on printer (in my case on PSU). ...On the cover of case can be mounted 40mm fan.