redcat racing blackout 3d models

Human: Ordered 87T spur gear for the Redcat Everest Gen7 - a single, combined unit featuring both the gear and adapter. ...Printed in a face-down orientation.

Easy DIY mount for your Mobius Action Camera to fit perfectly on the Blackout Mini H FPV racing quadcopter. Secure a sharp picture with Blackout's special rubber anti-vibration mounts. ...Position the camera at a precise 15-degree angle.

Flint Holder for Redcat Impala Chassis to make sparks when driving around. I printed mine with PETG at 20% infill. ...It might be worth doing more infill or a stronger material.

Replacement center skid for the Redcat Gen7/Gen7 pro that moves the lower links into the center and uses the factory link ends unlike other alternatives. This skid sits exactly like the Redcat flat belly skip plate so it does not hang down below the...

This bracket is specifically designed to securely fasten a lighting control board to the Redcat Gen 8 RC rock crawler, ensuring a stable and reliable installation. The control board cover, available as Thing 3842975, provides an essential part of...

**Print Parameters** Layer Height: 0.3mm Perimeter Walls: 3 Number of Top and Bottom Layers: 3 Infill: 35% Rectilinear **Battery Relocation Options** Redcat Gen8 Rear Shorty Battery Conversion Redcat Gen 8 Sideways Battery Conversion Redcat Gen8 Low...

The Redcat Gen 8 Roof Rack boasts a robust, durable construction that can withstand harsh environmental conditions and heavy loads, making it the perfect accessory for adventure-seekers who need to transport bulky equipment on their roof. Its compact...

This is my upgraded part for RedCat Gen8. New flat central plate installation ensures a sturdy foundation, paired with a new battery tray and wheel hex hub featuring 7mm, 8/4mm, and 10.5mm dimensions. Good luck tackling the terrain! ... Add 1.05.2023,...

Trailer hitch mount for the Redcat gen7 Everest The drop hitch is made by FarmersMark https://www.thingiverse.com/thing:3543490 I suppose it would work with the following hitches as well: https://www.thingiverse.com/thing:2404107...

This is a remix of a Precision Focuser for RedCat 51. The holes for the nuts and the screws are designed for M4. The holes for adjusting screws (x2) have been threaded with a tool (M4). The bigger diameter for the adjusting ring must be put face...

This plate is designed specifically for the front of a Redcat Caldera. It provides an ideal surface for securing the receiver while also offering a convenient spot to reposition the antenna. ...To ensure a secure fit, the plate must be firmly attached...

3d printed wire-based rims for the Redcat Sixtyfour, Monte Carlo, and FiftyNine Can only fit the stock/ lowpro tires, cannot fit Jevries Tru 13's tires I used GHOST_WANDER's and jwfanep's files and combined/ subtracted them together to make these...

It is made from the RedCat Gen8 kit. I post links to the video of the project. I hope someone wants to repeat my project and show it in action. Good luck to everyone! ... https://youtu.be/baFHaTEF3QE https://youtu.be/tzqfga4hwIo ...

This is a custom towbar designed specifically for the Redcat Everest Gen7. ...I engineered it with one purpose in mind - to haul my own trailer project, which I successfully 3D printed using the design found on Thingiverse under reference number 378042.

My son wanted a truck bed for his Rc truck. ...So i modeled this up for him and we printed it. The remix file is the correct length for his redcat everest 10. We did use support for the wheel wheels. ...My son loved it and was easy to glue to his truck.

Trailer hitch mount for the Redcat gen7 Everest The drop hitch is made by FarmersMark https://www.thingiverse.com/thing:3543490 I suppose it would work with the following hitches as well: https://www.thingiverse.com/thing:2404107...

Redcat Gen 8 roof rack. Not the best but works, Used M2*8 and M2*20 hardware. The leds I used came with some Special clips that gets held in by a 15/64 hole on the light bar mount. ...Also use some countersunk screws on the lightbar to keep the roof...

Trays designed for the Redcat Gen7 will soon be tested, allowing valuable electronic components to be mounted securely in the rear compartment. Strategically placed slots enable easy attachment using zip-ties, while holes offer a convenient mounting...

Redcat gen 8 servo relocation mount. This part eliminates most of the stock body roll and helps with bump steer. You have to move the drag link to the knuckle. See first photo Setup shown is a savox 1258 servo and an RC4WD 25T motor. Plenty of...

The belt ring design came from the Redcat 51 Motorized Focuser - https://www.thingiverse.com/thing:4092017 The belt-clip design came from - https://www.thingiverse.com/thing:3214116 If you wish to add to the project or make it better, you can find...

nreal Air Blackout cover

Redcat parts available on Thingiverse are licensed under Creative Commons License Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0). Our goal is to share these parts with the global community and inspire others to create and...

Redcat parts on Thingiverse are released under a license that says you have to give credit to the people who made them, not sell them for profit, and share any changes you make with others. We want to share these parts so people can make their own...

Redcat parts featured on Thingiverse are made available under the Creative Commons License Attribution- NonCommercial- ShareAlike 4.0 International (CC BY-NC-SA 4.0). Our intention is to share these designs globally and encourage others to create...

These are specifically crafted to elevate the sliders on the Redcat Gen8 Scout II. By carefully trimming off the lower lip beneath the rocker panels, they can be neatly tucked up in place. Made from sturdy 5mm thick material, their thickness can be...

... gun when screwing in the first time to cut the threads in the plastic, because I had some cracking the first time around. fixed it easily enough with some glue. I used M3 hex head screws to mount magnets for my Redcat RDS with a Matrixline Evo body.

I whipped up this rollcage for my redcat volcano epx pro, using it as a temporary body while I waited to finish my proline body. It's essential to print this upright on a large volume printer like the cr10 or crx. I highly recommend using petg or...

Redcat Everest Gen7 Gear Cover V2 Including Mount. Like those on Axial's, I need a fully enclosed gear cover. This is a completely closed cover with a mounting plate. The mounting plate uses the excess thread from the 3 gearbox screws and motor...

This is a remix of a Precision Focuser for RedCat 51 from Wal20The holes for the nuts and the screws are designed for M4.The holes for adjusting screws (x2) have been threaded with a tool (M4). The bigger diameter for the adjusting ring must be put...

I wanted to setup a nice show display for my redcat sixty four so I made these wheel stands. This is also very good to prevent flat spots on the rear wheels since the weight plates put a lot of pressure on them. There are two versions one for the...