redcat gen 8 axle mounted servo 3d models

In keeping with the non-commercial clause of this license, if you produce these parts (Gen 8 Sideways Battery Tray Mount.STL) + (Gen 8 Sideways Battery Tray Top Shorty.STL) or (Gen 8 Sideways Battery Tray Mount.STL) + (Gen 8 Sideways Battery Tray...

In line with the non-commercial clause of this license, if you produce this part (Gen 8 Rear Storage Rack.STL) + (Gen 8 Rear Storage Rack Mount.STL) for others, you may not receive compensation in excess of $5.50 per part, plus shipping costs. ...This...

In keeping with the non-commercial clause of this license, if you produce these parts (Gen 8 Rear Shorty Battery Mount.STL) + (Gen 8 Rear Shorty Battery Tray.STL) + (Gen 8 Transmission Brace.STL) for others, you may not receive compensation in...

This is the low-back rear seat designed specifically for the Redcat Gen 8 Axe Edition. To assemble the seat, utilize the 2mm socket-head screws provided with the Axe. ...The seat can be secured using either screws or double-sided adhesive.

The spare tire carrier allows you to mount your Jerry Cans and Hi-Lift Jack out of the way, giving a very scale appearance to the Gen 8. You will need a long 4mm screw to mount the stock wheel, as well as two 3 x 8mm screws to mount a Bead Lock...

This is a license plate light housing specifically designed for the Redcat Gen 8 International Harvester Scout II scale crawler. Additional hardware needed to complete this project includes one M2x8mm cap head screw. To install, begin by drilling a...

This is a rear hatch handle for the Redcat Gen 8 International Harvester Scout II scale crawler. Additional hardware needed: 1pc: M2x8mm cap head screw To install, you will need to drill a 2mm hole through the body in the desired location. Using...

These are frame rail screw brackets specifically designed for the Redcat Gen 8 International Harvester Scout II scale crawler. They become essential when you decide to remove the stock fenders from the chassis. Without them, tightening the screws...

Redcat Gen 8 Front Skid Plate. Supports are necessary at 1.5 layer height. It is strongly suggested to use 80 percent or more infill for maximum strength. This part was printed in carbon fiber filament and it's very strong and solid. PLA should work...

This is a short nosed front shock mount for the redcat gen 8, specifically for the creep body but should work with most shorter bodies, It has a few tweaks other than just being shorter, The bumper mounts are slotted to allow many different bumpers...

Designed for use with Redcats rear shorty battery conversion, using 2200mah 105x33x24mm batteries instead. ...Will bolt straight to their conversion plate

I wanted to amplify the scale realism on the Gen 8 model, so I crafted these hood louvers for the body. The concept is to carve out the shape of the inner black piece on the hood stickers, slide this in with the 2mm lip securing it tightly. Some...

Shock Spring Retainers for the Redcat Gen8 and Gen7 stock shocks. There are 2 styles, one clips on the shock and has a hole to use a wire to secure it in place to prevent loss (not required) the other you unscrew the bottom of the shock to install.

This is a short nosed front shock mount for the redcat gen 8, specifically for the creep body but should work with most shorter bodies, It has a few tweaks other than just being shorter, The bumper mounts are slotted to allow many different bumpers...

Can be mounted standalone, Or Used Under original Ring just needs longer M2 hardware.

Battery Tray Mounts Battery Location Just Above Transmission If You Plan To Build An Interior, This Tray Allows You To Move Battery Under Hood Of Scout And Hide It Behind Dash Once Installed - This Will Only Fit A 2S Battery. You'll Need To Modify...

This is version 3 of 3 different designs for alternative ESC/Receiver mounts that work with the Redcat Gen 8 International Harvester Scout II scale crawler. If you're using narrower aftermarket bodies, you'll have to move the receiver and ESC because...

This is version 2A and 2B of three different designs for alternative ESC/Receiver mounts for the Redcat Gen 8 International Harvester Scout II scale crawler. When using narrower aftermarket bodies, you'll need to relocate the receiver and ESC since...

This is version 1A and 1B of 3 different designs of alternative ESC/Receiver mounts for the Redcat Gen 8 International Harvester Scout II scale crawler. When narrower aftermarket bodies are used, you'll need to relocate the receiver and ESC since the...

Hi guys, This is some fender wells for the Redcat Gen 8 that allow you to install a cheap Chinese Jeep body shell. The Jeep shell isn't special, I just didn't want to destroy the Scout II body in freezing winter weather. I ordered two and one showed...

Hi guys, If you're as frustrated with Thingiverse's speed as I am, consider checking out Cults 3D for your 3D printing needs: https://cults3d.com/en/users/WrenchToDrive/creations These fender wells are designed specifically for the Redcat Gen 8 and...

Gen 8 Servo Mount, made to work with the Husky (short)Link set. ...All holes have been made to 2.8mm to fit 3mm screws with tension.

Hi guys, This is a cage for the Redcat Gen 8 for use with a cheap Chinese Jeep Wrangler body shell. The Chinese shells are a little shorter than normal, so this doesn't work 100% with name brand shells as-is, the front and back sections are about...

International Harvester (IH) logo receiver hitch plug for Redcat Gen 8 Scout II - Direct Factory Replacement. This replacement hitch plug is designed to match the factory "Redcat" appearance that comes with the vehicle out of the box. The one shown...

added another front link mount to try to 4-link my gen 8

Hi guys, This is a cage for the Redcat Gen 8 for use with a cheap Chinese Jeep Wrangler body shell. The Chinese shells are a little shorter than normal, so this doesn't work 100% with name brand shells as-is, the front and back sections are about...

Hi guys, This is a heavy duty bush bumper for the Redcat Gen 8 or an SCX10 clone. I mounted it over the frame rails with 2 screws going up through the stock bumper mount but I included a variety of mounts to use with the bumper. Printing the mount...

This block fills the void in the center skid plate for the Redcat Gen 8 International Harvester Scout II scale crawler to keep the rear upper link screws firmly in place without using lock nuts. The factory uses these nuts to prevent loosening due to...

Hi guys, The mount up for this cage is Redcat specific but you don't have to do much to it to make it fit an SCX10 or clone. The pics show it mounted to the Injora Ford body shell. Build is very similar to all my cages - please refer to the blog...

This design is slightly wider than the bumper Redcat supplies with the truck, aiming to match the factory body lines. Additional refinements have been made to the bumper and lens package. The lens boasts a 0.12mm gap around its edge, necessitating...