redcat 51 3d models

A rail to allow fitment of a dovetail guidescope and a laser to the William Optics Redcat 51. ... Works well.

Redcat 51. Dovetail slot for guide scopes and picitiny rail to mount an airsoft style laser for aiming. The 4 holes on the dovetail accept threaded inserts to secure the scope with screws. Simply heat up on soldering iron and insert. Working well for...

There is a built-in rotator in the RedCat 51. It's manual but uses a finely graduated ring with degree markings to set precise angles. By lining up a pointer on the rotator to the markings on the ring, accurate settings can be achieved. The problem...

This is a remix of a Precision Focuser for RedCat 51. The holes for the nuts and the screws are designed for M4. The holes for adjusting screws (x2) have been threaded with a tool (M4). The bigger diameter for the adjusting ring must be put face...

The belt ring design came from the Redcat 51 Motorized Focuser - https://www.thingiverse.com/thing:4092017 The belt-clip design came from - https://www.thingiverse.com/thing:3214116 If you wish to add to the project or make it better, you can find...

This is a remix of a Precision Focuser for RedCat 51 from Wal20The holes for the nuts and the screws are designed for M4.The holes for adjusting screws (x2) have been threaded with a tool (M4). The bigger diameter for the adjusting ring must be put...

This is my bespoke precision focuser designed specifically for the RedCat 51 telescope. I scoured Thingiverse but couldn't find any focusers tailored to my scope, so I decided to create one from scratch. After experimenting with a couple of existing...

This is the motorized focuser for my RedCat 51 telescope. I've already published my manual precision focuser (https://www.thingiverse.com/thing:3913819). This project builds on the same DNA as that one but with a stepper motor drive. The design...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Gear Ring uses: Qty 2: M4 Square Nuts Qty 2: M4 x 20mm Socket Head Cap Screws EAF mount is attached between the Redcat and Dovetail using: Qty 2: M6 x 50mm Socket Head Cap Screws and 1 M6 x 15mm Socket Head Cap Screw with M6 Nut There are 2 AIR...

As the built-in field rotator indicator of the RedCat 51 cannot easily be adjusted to the 0 position of the scale, I found it more convenient to have a freely adjustable indicator as part of the distance ring. RedCat 51 has a backfocus distance of...

As there is no matching glass solar filter for the Williams Optics RedCat 51 telescope so far and the smallest available glass filters are still too big, I constructed this simple adapter for glass filters made for apertures from 79mmm - 86mm. ... The...

This is a remix of https://www.thingiverse.com/thing:86136 The RedCat 51 telescope can be mounted with the ZWO EAF autofocuser, see https://www.thingiverse.com/thing:4683480. Note I bought the EAF mount before I got a 3D printer, so this is not a...

This is a base for a solar finder with a tight fit for the Williams Optics RedCat 51 Cat Series Saddle Handle Bar. Useful if the solar finder is used in exchange with e.g. a red dot finder for night observations. ...With the tight fit the finder stays...

Baader 110mm : Ecosize OD 5.0) holder for Redcat 51.Step 1: cut the solar filter foil in circle (use holder and sharpie marker to draw circle)Step 2: glue solar filter in holder and glue lid on to of itStep 3: glue indicator opposite to lid on holder...

This is a rail for William Optics RedCat 51 with a tight fit to the dovetail of the Cat Series Saddle Handle Bar. This allows to mount and dismount e.g. a red dot finder without losing the alignment with the main optics. Useful if the telescope is...

This is a mount for the ZWO ASIAIR, ZWO EAF, and guide scope to the Redcat 51. It uses a printed bracket and gear. You will also need: SmallRig Seamless Focus Gear Ring (72mm to 74mm) - 3293 for the printed gear to move the helical focuser.

Remixed from the original because I seem to have a different kind of field rotation ring than the original author. This works by attaching to either the first or second ring of the rotator with a tight interference fit. While sizing was the...

Remixed from the original because I seem to have a different kind of field rotation ring than the original author. This works by attaching to either the first or second ring of the rotator with a tight interference fit. While sizing was the biggest...

Got the starlight instruments focus motor and then had no way to mount the guide scope or reddot finder.

This is a dovetail adapter to be used with a Redcat51/Spacecat51. ...Can be used with a number of accessories, but was made specifically for my focuser: https://www.thingiverse.com/thing:5140885

This is a riser block for the EAF/RedCat mount ( by domino89 / thing 4883844 ) to prevent the EAF from hitting the EQ6R knobs. I used the ARCA slide mount to fit this onto the bracket of the RedCat. The top side edges help to align the scope...

Redcat 3dprinted adapter for pegasus pocket powerbox and pegasus focus cube V2. I hate belts so I designed a custom mount focusing ring and pulley to focus gear to gear. Works with both my QHY268C and ASI183MM and it is so reliable and precise that I...

This is just another way of fixation for ZWO EAF to William Optics 51 series telescopes. I wanted to keep the center of gravity as low as possible. I printed it with my Dremel 3D20, it fits perfectly. It is design for 280mm long GT2 belt, 6mm...

Problem: - taking calibration frames is very important for deep space astrophotography. The traditional method is "a white T-shirt and tablet (light source)". That's still the answer even if you have a >1000 USD telescope. It leaves dust, and after...

Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627

This is a tool to measure the backfocus distance of a ZWO ASI6200 MM/MC Pro camera attached to a Williams Optics RedCat 51. The backfocus distance is the distance of the focal plane to the back side of the telescope. In case a filter wheel and an...

Ellumiglow Flat Panel for Redcat 71 and Redcat 51 Uses 5” Ellumiglow Product with Acrylic https://www.ellumiglow.com/electroluminescence/astrophotography

This is a Vixen Dovetail adapter for the William Optics RedCat 51. Use it to mount my ZWO 30F4 mini guidescope. Used the upper part of this https://www.thingiverse.com/thing:3742835 and changed it. ... Supported the mounting screw hole for the...