rear enders 3 3d models

I did a remix of the popular enclosure by Teaching Tech because it didn't required T-Nut to fix it to the printer and I only needed the left part for the Raspberry Pi. I also preferred the fan blowing under the unit. It has enough room for the...

I found a useful support on the site, but it had some flaws. With the slicer, we had ghost volumes in the room, which resulted in being unable to introduce captive screws. I took up the concept and redesigned the model completely. This model does...

This is a modified version of CHEP's design. I saw a post of a remix that someone made that goes on the side so it doesn't interfere with the cable chain, but I wanted to make my super-short version of it, I also added a filament guide that I...

This is a remix of part from the original model https://www.thingiverse.com/thing:3808088 I only added the slider so that I didn't have to use a t-nut, which I didn't have.

Details: - I really liked Marvinda's "Ender 3 (Pro) - Raspberry Pi Model B+ Case for OctoPrint with Relay Control." https://www.thingiverse.com/thing:3384729 - I wanted to do the same thing but mount it in the rear of the Ender3 underneath the power...

The right side is a remix of the SKR 1.3 mount created by makermelissa that includes mounts for two buck converters: https://www.thingiverse.com/thing:3901224 See the remix by DavidETurner for a better cooling duct design and Raspberry Pi 4:...

This is a remix of the original "Ender 3 all in one, universal rear electronics case" from Michael's Teaching Tech channel. Check it out on Thingiverse: https://www.thingiverse.com/thing:3688967 I've updated this model to work seamlessly with Orange...

I've got these feet attached to the bottom of my Ender 3, which allow for a non-flat table top and extra cooling underneath for my Raspberry Pi: https://www.thingiverse.com/thing:3109537. Taking advantage of the extra space under my Ender 3, I...

Most direct drive extruder plates for Ender 3 series are designed to mount the original extruder motor facing the front, with the extruder facing the rear, which can be troublesome to use when loading filaments. By using a left-handed extruder,...

New Covers, if you want to make both 40mm fans to do a push

Just a remix for the E3 Turbo. Closed walls improve the airflow very much - air is sucked from the right so the left directly over the stepper drivers. Also it is extremely silent a with 92mm angled slim Fan powered by a DCDC Converter @ 7-8V is...

This is my first remix. There were a couple different reasons I started this remix. One is I wanted to change most of the screws to use heat-set inserts, allowing for easier disassembly/reassembly. I also had no need of the buck converters or relays....

<p>Really liked the original version of this, but when using the mirrored version you can't use a cable chain, so modified it so that there is a channel for the bed cables and a mount for the cable chain to attach to. ...&nbsp;</p>

The relay is 30A to switch power to the Ender mainboard. I added a BME280 temperature sensor to the Pi3B and placed it next to the SKR board, maximum temps I am getting are in 30-35C range (so pretty good). The right fan blow in across the...

Needed to have a honeycomb grid at the top.

I just remixed the right lid so that i could fit a low profile 80 mm fan on top instead. i positioned it quite tight with the stepper motor so have that in mind when you mark out your holes and drill them. I just marked the holes and drilled with...

I had trouble getting the original to fit, it was off, oddly, by ~4mm so I made this a bit skinnier. ... I've always had parts end up smaller (shrink) so it's kind of baffling why this one ends up too big.

A minor remix I made for personal use using the model uploaded by "edtse88" I replace the bottom face with a squared mesh, as the original had some unnecessary geometry, and replaced the hexagonal design with a slotted design for the grills. ...

Just remix for SKR mini e3 motherboard

UPDATE: My remix has one critical flaw - it lacks an exit hole for the power supply cable. I strongly advise against printing it right now. As per Kooftness' request, I created a revised version designed specifically for the PI side to use...

A protective shield for the right side of the enclosure crafted by TeachingTech, featuring holes specifically designed for an 80 mm fan. Please note that a 25 mm thick fan will not fit within this configuration; instead, use a 10 mm thick fan...

This is actually a remix of sheppard47's remix of Teching Tech's AIO electronics case. (https://www.thingiverse.com/thing:4639576/files) The standoff location is correct for the SKR Mini E3 v3, but the plastic tabs for the heatsink stick out too far...

I designed this modification because I wanted to relocate the extruder attached to the top of the frame to the side of the X-axis to improve filament routing. It's based on Creality's open-source files, so dimensions should be accurate. You'll need...

This is actually a remix of sheppard47's remix of Teching Tech's AIO electronics case. (https://www.thingiverse.com/thing:4639576/files) The standoff location is correct for the SKR Mini E3 v3, but the plastic tabs for the heatsink stick out too far...

Added a cover for the vent holes to prevent filament from being able to enter PSU case

Combined right mks gen l from https://www.thingiverse.com/thing:3688967 with drag/cable chain connector from https://www.thingiverse.com/thing:3690894 Update: Added the Fusion 360 file, it's just the imported STLs did the "Mesh to Brap", cut the not...

I combined the right mks gen l from https://www.thingiverse.com/thing:3688967 with a drag/cable chain connector from https://www.thingiverse.com/thing:3690894. Update: I added the Fusion 360 file, which simply imported STLs did the "Mesh to Brap,"...

Update 8/13/2019: The lid for the Pi side is now optimized to work seamlessly with the Ender3, replacing the previous version designed specifically for the Ender3Pro. Remixed half of this project for a friend and will share photos later. ...The Pi side...

Supportless version of tdogg450's Rear Ender 3 V2 Dual Chain Mount.

Modified adjustable endoscope mount for Ender 3 v2.