rear dash cam mount 3d models
427730 3d models found related to rear dash cam mount.prusaprinters
Got tired of the cam constantly falling down as no sticky tape/pad would stick to the plastic cover on the boot lid “roof”.In the end I decided to make a simple mount that hooks on the plastic cover and keeps the camera in place.Printed with PETG to...
thingiverse
This is a universal Rear Dash cam mount designed specifically for the 5th Generation Toyota 4Runner. It secures directly into the back seat belt hook's holder location. The back seat belt hook has a protective cover that opens with a slight pop,...
thingiverse
Rear dash cam clip mount for 2022+ Tundra with full rear sliding window. Clips on to black trim. Just pull trim down, insert clip, then push trim back into place. ...Print in PETG to avoid warping in the sun.
thingiverse
This is the rear mount for the K1S dash cam in a BMW 1 Series Convertible (E88). It clips into place on the rear vent and under the roof cover, requiring no adhesive at all - simply mount your camera on top of it (you'll need to invert the camera...
thingiverse
... would fit other SPA platform Volvos. Installation instructions: Peel back the weather seal on the top of the trunk and slide the hook onto the headliner. You can tap 12v power from the rear fuse box and run the wire under the trunk weather seal.
thingiverse
Installing a rear dash cam in a Porsche 991.2 can't easily be done. ...This design is a mounting bracket that can be slit over the edge of the roof trim and so give a mounting point for a dash cam
thingiverse
It mounts to the rear view mirror for a 4runner but can be adjusted to fit by changing the diameter of the mount. You could also change the width for the camera mount if you have a different camera. It will require 2 M4 bolts and nuts. ... Length...
thingiverse
I needed a mount for my dash cam because the suction cup was messing up my windshield tint. I would print this out of PETG or similar due to the heat. PLA+ works but gets very soft. ...I used 3M double sided automotive tape to mount it.
thingiverse
This is a mount for a standard, cheap [yi cam](https://smile.amazon.com/dp/B01CW4ASS0) Simply wedge this up by your rear-view mirror and run a long [usb cable](https://smile.amazon.com/dp/B073PT6Q1P) around your windshield
thingiverse
- Xiaomi Yi Smart Dash Camera mount - Didn't want to remove original mount from my car when I traveled abroad and wanted to use the camera in rented vehicle... ... - Printed in PETG, 236C, 100%infill, 25% fans - Use thick, double sided tape to stick it...
cults3d
Adaptor to make use of the redundant rear view mirror mount in my Vito van. I re-used the threaded mount section from another nextbase design on here. Designed in Fusion 360. ...Printed in Carbon Fibre PLA at 20% infill.
thingiverse
My holder for the cam broke, printed a replacement mount with petg but the sun melted and deformed the piece. So made this to hold in place even with sun exposure. You have to cut the holder of the original holder. ...Mine was already broken so had no...
thingiverse
I repurposed a redundant rearview mirror mount for my Vito van, finding innovative use for it by adapting a threaded mount section from a different Nextbase design. ...I crafted the adapter using Fusion 360 software and printed it with high-strength...
thingiverse
Spare 70 mai dash cam mount. ...Mount with two sided tape to windshield.
thingiverse
This is a sleek Yamaha golf cart mount designed specifically for the Rove R2-4D dash cam. The mount securely attaches to the 3/4-inch rod that supports the center rear view mirror, providing a stable platform for capturing high-quality video. A...
thingiverse
Garmin Mini Dash Cam Replacement Mount is designed to securely hold your device in place on any windshield, providing a clear view of the road ahead while keeping your hands free to focus on driving.
thingiverse
My G90 dash cam is a game-changer, but the flimsy mount that came with it was a major letdown. It kept slipping off my windshield. I took matters into my own hands and searched for a better solution on Ebay. I finally found what I needed - the...
thingiverse
The Lukas Blackbox dash-cam comes with a convenient windshield mount. If you misplace it, simply print out a replacement and secure it firmly in place using VHB tape on your windshield. ...Just be mindful of its position, as the mount is fixed and...
thingiverse
Compact Mount for Nextbase Dash Cams Fits My 522GW and Possibly Others with the Same Design Fixed Angle of 30 Degrees Suitable for 2005+ Aygo Models Simply Assemble the Two Pieces Together by Pushing or Gluing Them, Then Attach to Your Windshield...
thingiverse
I created a Dash Cam Mount that perfectly complements my Instructable "Dash Cam for under $20". Keep in mind that based on the design, adjustments might be necessary to suit the size of the suction cup hook you are using. Here's how to assemble it: ...
prusaprinters
This mount adapts the stock rearview mirror stalk to some common rearview mirror dash cams available on Amazon under many brands. I can't be 100% sure which ones it will fit. The model/brand I designed it for no longer exists.I installed mine on a...
thingiverse
... Thanks To Normal Turn, Acceleration, Or Deceleration Actions, Resulting In Unwanted Camera Movement. On An Added Note, If You Happen To Be Using AutoGuard As Your Preferred Dash Cam Application, It Might Come In Handy While Utilizing This Setup.
cults3d
I use my Note 2 phone to listen to music while driving, wanting to utilize its camera feature as a dash cam as well. It seemed like another ideal opportunity to create a custom mount. To avoid suction cups that could detach and keep it away from...
thingiverse
This dash cam mount is designed specifically for the Z-edge camera, adapting it to fit on a Subaru Outback's rearview mirror mount. The necessary files in Fusion 360 are included, allowing for modification as needed. The mirror post accommodates a...
thingiverse
I encountered an issue with my original mount breaking, prompting me to find a creative solution by modifying two different mount files to perfectly fit my trusty dash camera. The model I'm utilizing is the B01CSOD7VO, available on Amazon -...
thingiverse
I decided to design a replacement mount from scratch. After scouring numerous options, none of them fit my car or meshed with my mirror. I took three distinct prints and merged them into a single model that perfectly aligned with my vehicle's...
thingiverse
That being said, the "long" mount should work for just about any vehicle that has this shape of lip on the rear of the headliner and the "short" mount should work for almost any headliner in almost any vehicle. Simply pull down the back edge of the...
thingiverse
Hi It’s a rear dashcam mount design for “fitcamx” cam but I believe many brands use the same camera, I designed this because I wasn’t happy with the glue mouth cause the hot weather in here i refit the cam ever single day lol. This mount hocked...