rcbs primer catcher 3d models

Replacement fastener for RCBS Primer Catcher fastener.  If you reload your own bullets, and have an RCBS reloading press with a primer catcher, but have broken or lost the little crecent-shaped fastener piece that holds it in place, instead of buying...

I love the new primer catcher my RCBS Rock Chucker sports:http://www.thingiverse.com/thing:1223108 Might also work with this primer catcher:http://www.thingiverse.com/thing:148190, Or its predecessor:http://www.thingiverse.com/thing:84047. While it...

My version of a primer catcher for RCBS Rock Chucker. Basically same as original with tube adapter that works with case ejector. ... I printed in two pieces and glued together.

My DIY take on a primer catcher for the RCBS Rock Chucker, essentially a modified version of the original design with an added tube adapter that seamlessly integrates with the case ejector. ...I opted to print it in two separate components and assemble...

i dont have magnets but i have a ton of cable ties, so i put holes in it i had a lot of issues with LRP's getting hung up near the part-tube junction, and some primers falling out, so i'll prob have to do a lot more design work to this

Primer catcher for the RCBS Summit press. You'll need 1/2" ID tubing and you might need to dip the tubing in hot water for a minute to get it to slip in place. I secured mine with a wire tie. ... Print at 100% infill.

It's held securely in place by six 6.3mm diameter (1/4 inch) Neodymium magnets embedded in the rear of the catcher. The holes are slightly undersized, allowing for a snug fit or requiring some reaming to ensure a perfect fit, which was exactly what...

This catcher will only work with the RCBS model displayed in the image. It comprises two components that must be joined together using adhesive. If your printer is accurate, it should not require any screws for securement; my example clicks into...

It is necessary to shave off a bit inside the hose to prevent that spent primers get stuck before sliding down the tube. There are 4 indentations in the back for 10 x 1.5 mm magnets. I don't use them because it fits snug onto the press without...

It is necessary to shave off a bit inside the hose to prevent that spent primers get stuck before sliding down the tube. There are 4 indentations in the back for 10 x 1.5 mm magnets. I don't use them because it fits snug onto the press without...

This is a remix to use 9 mm garden hose with this spent primer catch. These hoses have a 15 mm outside diameter which fit snug into the device. It is necessary to shave off a bit inside the hose to prevent that spent primers get stuck before sliding...

Minor remix to make the holes for the magnets larger so I could use the magnets I had on hand. ... These are for 10 mm x 1.5 mm magnets, and on my printer were a nice "snap" fit and didn't require any trimming or glue.

The Rebel Press uses a 1" diameter piston rod, and the primer catcher slides up and down on the rod, so some play in the plastic tube is necessary for it to function. ... You will need 1" clearance between the Rebel press piston rod and the front of...

This is a precision-made primer catcher designed for use with the RCBS JR2 reloading press, ensuring spent primers land safely in one place rather than scattering all over the floor. A sturdy trash can can be positioned directly below the spout or...

This is a Remix of Older model RCBS Press Primer Catcher by bitbizsyd. I modified it to use it with 12mm (0.47") hose (press fit). ... Print it upside-down using support for the pipe

Still struggling to locate a suitable primer catcher for my RC2 setup, which I'll refine over time as needed. My initial attempt is functional, albeit requiring some adjustments later on. The design necessitates reversing the RAM configuration and...

Primer catcher for the rock chucker supreme press. I tried a few of the models out there and they did not work to my satisfaction. This was designed to fit the press with no tools or pins. It has clearances for any rough castings and should fit your...

Thsi Prime catcher has been desgned for an older version of the RCBS Rock Chucker Supreme press, having the outlet for the primers at front side. The catcher can be attached to the press by pressing into the 4 mm holes threads for M3 screws. For...

I've yet to spot a Primer Catcher designed specifically for early model RCBS presses, so I took matters into my own hands and created one myself. To collect spent primers, I attach some clear tubing that securely holds them in place. ...For added...

This is a retainer for an RCBS Primer catcher. You only get this when you buy a new tray so I decided to print one. ...Feel free to upgrade this to your desire.

This is my take on the RCBS JR2 primer catcher. I used the one by @bcon123 as a starting point but basically redesigned it from the ground up. It mounts on the right side of the frame with 4 10mm x 4mm (I used 8 10mm x 2mm and stacked them)...

This is a RCBS Summit reloading press "Primer Catcher" design that bolts right up to your existing primer catch screw holes on the press. You can attach a hose that catches the spend primers or redesign the part as needed. ...

This is just the primer arm for the priming system of an rcbs rockchucker. This part is discontinued and the only way to get it is calling rcbs and having them send you one. ...I haven't tried printing this yet as I still have mine and mostly made this...

A primer catch for my RCBS Summit reloading press, as mine did not come with one. ...I liked the design I ended up with, so I'm publishing it in case anyone else would like one.

There are quite a few versions of these primer catchers but I wanted something specific. This replaces only the back half of the stock primer catcher. The catcher needs to flex considerably in order to install on the press and I wanted to maintain...

primer chute that does not suck.

* The primer catch was widened, eliminating issues with primers hitting the front sides and bouncing away. * The primer catch mouth was shortened, reducing the overall height of the unit by about 1cm. * The entire unit was made deeper to absorb...

primer catcher for lee press. ...holds about 300 primers

... A larger version has been added, which is twice as big as the original one. ... This is a straightforward bolt-on primer catcher with a small tray for use with the Hornady LNL Press. ...The tray should be able to hold at least 100-200 primers.

Replace the original Rockchucker II primer catcher with a new one. I think you can connect a 0.5 inch inner diameter hose to it - I haven't tried it yet. I made this in TinkerCad, so it's not as nice as some people's, but I'm proud of it. There...