rcbs bench primer 3d models

Primer tube and primer pin holder. ... Designed for the RCBS bench primer, but would work with others.

This is a RCBS Summit reloading press "Primer Catcher" design that bolts right up to your existing primer catch screw holes on the press. You can attach a hose that catches the spend primers or redesign the part as needed. ...

This is just the primer arm for the priming system of an rcbs rockchucker. This part is discontinued and the only way to get it is calling rcbs and having them send you one. ...I haven't tried printing this yet as I still have mine and mostly made this...

A primer catch for my RCBS Summit reloading press, as mine did not come with one. ...I liked the design I ended up with, so I'm publishing it in case anyone else would like one.

This is a retainer for an RCBS Primer catcher. You only get this when you buy a new tray so I decided to print one. ...Feel free to upgrade this to your desire.

My version of a primer catcher for RCBS Rock Chucker. Basically same as original with tube adapter that works with case ejector. ... I printed in two pieces and glued together.

 If you reload your own bullets, and have an RCBS reloading press with a primer catcher, but have broken or lost the little crecent-shaped fastener piece that holds it in place, instead of buying a whole new primer catcher, or trying to rig up...

I love the new primer catcher my RCBS Rock Chucker sports:http://www.thingiverse.com/thing:1223108 Might also work with this primer catcher:http://www.thingiverse.com/thing:148190, Or its predecessor:http://www.thingiverse.com/thing:84047. While it...

Primer catcher for the RCBS Summit press. You'll need 1/2" ID tubing and you might need to dip the tubing in hot water for a minute to get it to slip in place. I secured mine with a wire tie. ... Print at 100% infill.

My DIY take on a primer catcher for the RCBS Rock Chucker, essentially a modified version of the original design with an added tube adapter that seamlessly integrates with the case ejector. ...I opted to print it in two separate components and assemble...

primer chute that does not suck.

Occasionally a primer sits on the "shelf" behind the ram but it always ended up getting knocked down the tube by the next primer. I did not include a blocker for the front of the ram. I learned long ago that a drinking straw fills that space nicely...

This is a precision-made primer catcher designed for use with the RCBS JR2 reloading press, ensuring spent primers land safely in one place rather than scattering all over the floor. A sturdy trash can can be positioned directly below the spout or...

For all 2A enthusiasts that have this reloading press.While RCBS has some high quality reloading tools and materials, the primer catcher for the RCBS Turret Press is not one of those, and leaves something to be desired. The primer catcher that comes...

* The primer catch was widened, eliminating issues with primers hitting the front sides and bouncing away. * The primer catch mouth was shortened, reducing the overall height of the unit by about 1cm. * The entire unit was made deeper to absorb...

... a large one, allowing me to switch between sizes easily. ...Keeping them behind is better, but I left mine as is since it still works fine. This custom block makes it easy to organize everything for my RCBS universal hand primer bit on the pegboard.

I've yet to spot a Primer Catcher designed specifically for early model RCBS presses, so I took matters into my own hands and created one myself. To collect spent primers, I attach some clear tubing that securely holds them in place. ...For added...

Thsi Prime catcher has been desgned for an older version of the RCBS Rock Chucker Supreme press, having the outlet for the primers at front side. The catcher can be attached to the press by pressing into the 4 mm holes threads for M3 screws. For...

... to fit the RCBS Rock Chucker II press. ... This is useful if you want the primers to fall to the bottom of the ram and prevent them from spitting out the front of the ram and press. Also, made the magnet holes deeper for 5mm by 5mm magnets. ...

... or lose yours, you'll need another. ...This holds the primer catcher tray on the RCBS Rock Chucker reloading press. They sure don't make things like they used to. ...I've only been reloading with this thing for 42 years and already something broke.

RCBS Rebel Press primer catch tray. Check out v44 of this model on Thangs.com This is an add-on reloading part to a RCBS Rebel press. It uses (2) 1/16" x 3/4" bolts, nuts and flat washers to connect the two parts together. 1/2" inside diameter...

Primer catch tray to be used with common 3D printer primer catcher for the RCBS rock chucker IV. I was recovering unused primers and did not want them going down a tube to the waste bucket. Also works as a work tray on the right side of the press.

The Rebel Press uses a 1" diameter piston rod, and the primer catcher slides up and down on the rod, so allow some play in the plastic tube is necessary for it to function. The idea of a Cover piece came about because I sometimes need to remove...

This is my take on the RCBS JR2 primer catcher, and I built it from scratch using @bcon123's design as a starting point. The catcher mounts securely on the right side of the frame with four powerful 10mm x 4mm magnets, which I reinforced by stacking...

You'll need another one if yours breaks or goes missing, it holds the primer catcher tray on the RCBS Rock Chucker reloading press. They don't make things like they used to, that's a fact. I've only been reloading with this thing for 42 years and...

This catcher will only work with the RCBS model displayed in the image. It comprises two components that must be joined together using adhesive. If your printer is accurate, it should not require any screws for securement; my example clicks into...

It is necessary to shave off a bit inside the hose to prevent that spent primers get stuck before sliding down the tube. There are 4 indentations in the back for 10 x 1.5 mm magnets. I don't use them because it fits snug onto the press without...

... ten 1.5mm magnets. I choose not to use them because it fits snug onto the press without them. https://www.thingiverse.com/thing:4253130 I added a design for a Spent Primer Box that also fits the 15mm hose, ideal for mounting under the workbench.

The design necessitates reversing the RAM configuration and incorporating a ramp for the primer discharge slot. To print this model, I recommend using flat layers with support structures for the tube. ...If desired, you can secure it to your press using...

This is a remix to use 9 mm garden hose with this spent primer catch. These hoses have a 15 mm outside diameter which fit snug into the device. It is necessary to shave off a bit inside the hose to prevent that spent primers get stuck before sliding...