rc10t2 parts 3d models

... rest is probably just too small or made of metal. I hope this model inspires you to learn how to do some 3D modeling. If you manage to print parts of this, please take some pictures and post an "I Made One" under this object - I'd love to see them!

Front control arms for a Team Associated RC10T2. May fit other RC10 variants (GT?). Design is simplified for printing as shown in the picture. Only one arm in file - mirror for the other side as needed. I recommend stronger materials if possible.

Front bulkhead for the RC10T2. This has been modified slightly to make it easier to print (extending the shock tower mount to the front of the bulkhead). The hinge pin holes should be reamed out with a 1/8" drill bit. The chassis mounting...

Front bulkhead for the Team Associated RC10T2. This design has been modified to make it a little easier to print. It does not lend itself that well to being printed, but the middle portion between the shock mounts and the lower pivots has been...

Gear Cover for Team Associated RC10T2 Modified to Accommodate B4/T4 Style Dual Plate Slipper Clutch This customized gear cover enables the use of a dual plate slipper clutch in the same manner as the original, albeit slightly oversized. The design...

Front A-Arms for the Team Associated RC10T2. They should also fit well on the RC10GT. Ream out the hinge pins with a 3 mm drill bit and then use a 1/8" drill bit. It may take several passes but make sure the arms turn freely on the hinge pin...

... and tolerances of your printer. Centered ball stud provisions add structural integrity while maintaining original part height. ...By refining mounting holes within the material, this custom design ensures seamless integration with the chassis.

Front body mount bracket for the RC10T2. ... You may need to ream out the screw holes slightly, but 4-40 screws should thread in just fine.

Front body post mounting bracket for the RC10T2. ... This is not a very complex component, but print orientation will be critical to maintain strength.

Rear lower shock mount for the RC10T2. The holes for mounting the arm could be reamed larger to allow the screws to pass through more cleanly (if desired). ...The shock mounting holes should be tapped with a 4-40 tap.

The stock part is composed of nylon, so this part would likely be a "get by" unless you can print in a material of sufficient impact resistance. Ream the kingpin/hinge pin hole with a 1/8" drill bit. The front axle hole is slightly smaller than a...

The estimated stock anti-squat angle is approximately 2.5 degrees based on measurements of worn parts; however, it may be slightly higher, closer to 3 degrees. Many drivers racing this truck in its prime would reduce the anti-squat using shims, so...

Servo mounts for the RC10T2 and spacers for setting servo position. These are designed for a 0.2 layer height, so they are not an exact match for originals (2.4 vs 2.5 mm). These could easily be modified to match. ... Tap the mounting holes with...

Front mini bumper for the RC10T/RC10T2. This is designed similar to an OEM aftermarket bumper (RPM) that was available once upon a time. They are getting incredibly difficult to find on the web, and there are probably more durable options...

12 MM Hex adapter for RC10T/RC10T2 vintage R/C trucks to allow the use of Traxxas offset rear rims. Combine this adapter for the rear rims with the 5X11 adapter that I also have published and the offsets for the front and rear would be adjusted...

This design is basically a modified version of the Tamiya Super Astute remixed battery box that I modeled earlier, that has been modified to attach to the RC10T2 chassis. It also has built in slots to allow you to pass wires from one side of the...

Front caster blocks for the Team Associated RC10T2. This is the 25 degree version. ... Ream the hinge pin hole with a 1/8" drill bit and tap the ball stud mount with a 4-40 tap.

Front caster blocks for the Team Associated RC10T2. This is the 30 degree version (6210). Ream the hinge pin hole with a 1/8" drill bit and tap the ball stud mount with a 4-40 tap. ... If time allows, I may upload a 25 degree version (not that...

parts

machine parts

Random parts

important part

Different parts and drawings.

this parts designing project

This is a mechanical part

This is a mechanical parts

Parts for the holiday table

This is a mechanical parts disign

Just simple parts worm gear ball bearings and a shaft for I-parts in Inventor and I just added my trainsmition and chain.

A collection of many parts ranging from gears to crisscross to small models.