rc trireme 3d models

Purchased an "Excell RC folding 8x4.5" prop for use with my Eclipse model and found that the spinner cone itself was too large for the plane model, but the base plate was almost perfectly sized. So using the original part's rough measurements I made...

1/10 - you might use it in RC car also or with a bit of scaling. For assembly you will need M3 screws with coutnersund head. Ideal length is M3x10, but holes in the seat are through the shole seat, so you can use whatever you have on hand. For...

Electric Motor Build: Motor: Mabuchi 12vdc RS-385PH-1470 https://www.ebay.com/itm/Mabuchi-12V-DC-Motor-2100-2900-rpm-DUAL-SHAFT-hobbies-RC-CARS-LOT-of-4-motors/162123316361?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649 Wire: 18ga 2...

I actually wanted to use the TPU for printing wheels for RC projects ( :( I never came around to those ) but since It was even printing some mechanical/moving parts just great I decided to throw a bunch of stuff at it, this model included. I was...

Stutzen mit Damperfunktion - 4 x Zylindermagnete Durchmesser: 4mm Länge empfohlen: 5-6mm (Magnete können auch kürzer sein das Loch ist 7mm tief und sie müssen eingeklebt werden) https://www.neomagnete.de/de/stabmagnet-4x6mm-neodym-42sh?c=28 - Servo:...

It uses a pair of these dampers: https://www.aliexpress.com/item/Hsp-hpi-hop-up-parts-oil-adjustable-130mm-alloy-aluminum-shock-absorber-damper-for-rc-car/32593123945.html?spm=a2g0s.9042311.0.0.Q01WaR I set the dampers to their stiffest setting,...

You may find more information about this work on Tamiyaclub, Tamiyabase, rc10talk or Vintage-RC. I modified the stl to take into consideration the issues I found during the build, but have not reprinted the parts to double check. In case you...

Attaching this module to an RC model allows for easy tracking in case of an unplanned landing. Once energized, the module attempts to acquire a GPS fix and emits a short beep every 15 seconds. Every five minutes, it transmits coordinates and status...

The bot can be controlled using a Bluetooth connection, I recommend 'Arduino Bluetooth RC Car' for Android (not tested with iPhone). The source code and build instructions are available at: https://github.com/christianp007/Balancing-Bot If you need...

*** Last Update (21.08.16) *** Joined 3 locks into 1 part for easier printing Use brim option to minimize any errors during printing Just incase if you are not accessible to 3D printer, you can buy the printed part from my shapeways shop below :...

In this discription you will learn how to cast onroad tires for your rc car by your own. The outer diameter of the wheel is 75mm and the widht is 40mm. For the rim you can use pla or petg. For one tire you will need 60g black sanitary...

Belt link (245mm 49teeth) - https://www.aliexpress.com/item/5pcs-lot-5M-Timing-belt-230-5M-15-teeth-46-Neoprene-width-15mm-length-230mm-HTD230/32251844016.html?spm=a2g0s.9042311.0.0.7JLrmV Motor (5045) -...

The drive uses two 25 tooth, 5mm shaft gears (RC cars parts) for the motor to drive a layshaft that runs in in brass tube bearings in the PLA frame. This shaft carries two 9 tooth Meccano sprocket wheels driving chains down either side to two much...

If you want to help, give me a follow on instagram @ nav.labsIf you have any questions about the project or how to assemble it, feel free to message me on instagram.Here is the links for all the parts on...

However, as long as I know, gyro on RC Drift works better if you put it as low as possible, so I design this gyro holder. If you have old WPL D12, you can use this version by GTnos that even have lower center of gravity:...

Common silicone 14+ gauge wire used for RC applications is probably too thick, but good old inflexible Home Depot copper 14g cable has thinner insulation and fits fine. ...A pair of right angles were bent into the wire to allow a tight fit against the...

Inspired by the Charging Case created by Turtle laboratories (https://turtlelaboratories.com/blogs/projects/portable-field-charging-box-for-isdt-q6-rc-charger), I decided to create my own field charging kit using the newly acquired ToolKitRC M8 smart...

The smaller gear was installed on the axis of a standart RC Servo Motor, previously modified to remove the electronics, potentiometer and the stopping pin (For instance, you can see how to do this in Youtube:...

This tire-press can be used for mounting tires onto RC beadlock-style rims. It is suitable for up to 1.9"-rims and 4.75" tires (if not silly wide). It helps to keep the tire with internal foam compressed, while fitting the outer beadlock...

ADDITION2: The micro works but i still wasnt happy with it so i made a bench sander from left over RC parts, added versions with the hole to changed to 3.5mm in order to fit the output axle on a hexTronik DT750. Also added air scoops to the large...

[--- german - english below ---]Die kleinen Federsplinte für RC-Karosserien sind nicht gerade schön und das Herumgefummel nervt mich furchtbar. Ich konnte leider keine Magnet-Halterung nach meinen Vorstellungen finden, daher habe ich giese entworfen....

### Features * Optional compartment for a 350mAh LiPoly battery (with a zip-tie strain relief slot) * Slot for a rare earth badge magnet (source provided) * Support for Adafruit's stackable Feather wings * Cable management and routing slots * Upside...

1:18 scale EC 135 electric r/c helicopterBuild thread on RC Groups https://www.rcgroups.com/forums/showthread.php?3835813-EC135-Scratch-BuildNote that this is a work in progress - comments welcome!Modified on 31/07/21 to update stl files for...

* Actualiza el sistema ```bash sudo apt update sudo apt upgrade ``` * Crea el usuario y dale los permisos necesarios ```bash sudo adduser octoprint ``` * Da permisos al usuario ```bash sudo usermod -a -G tty octoprint sudo usermod -a -G dialout...

It creates nice star spikes for astrophotography as if the secondary mirror would be held with arms like in a newton or RC telescope (or Hubble Space Telescope ;)). It is not made for visual observations. It is designed for my C8 from 1992 (black...

Working on a replica 1:1 Scale of the Exocomp from Star Trek TNG.  Goal is to be as accurate as possible and build with RC motion and LED Lighting/Sounds This is a work in progress and not all files are available yet. file will be updated as I go....

-If you like this design, please follow me, as I release all sorts of things, from slot car stuff, Rc hobby parts, to phone cases and Hobby/Office organizers. More to come soon! Enjoy! (Please comment If you have any questions!) Oh... and...

Here is the categorized list: **Flight Controller** * Flight controller + http://www.gearbest.com/flight-controller/pp_623876.html?lkid=11005051 +...

There are 2 DC motors, those little 6-12V ones that come in most RC car kits, which are used to control the winch. The winch is attached to the catapult arm via some copper wire. There is a limit switch, which is used to determine when the catapult...

I used silicon to glue the tire onto the rims because the TPU was not flexible enough for the normal Open RC Truggy rims. Tires are different in the middle section of the profile. If you have questions or need parts, leave a comment or write a...