rc transmitter holder

Hot Shoe Speedlight Mount (remixed mic mount)
thingiverse

Parts: 1x BC547 1x 1500uF 16v Electrolytic capacitor 1x 1n4002 Rectifier diode LEDs and resistors for LEDs How I Designed This I remixed the adjustable hotshoe microphone holder. http://www.thingiverse.com/thing:346513 After adding this to 123D...

PIRANTULA - A powerful hexapod / spider
prusaprinters

1x Fuse Holder - In case of things going bad! Link 2x 20A step down modules Link various brass standoffs Link Tons of cable ties Link Various 30A power connectors - Link Print Settings Printer Brand: Creality Printer: Ender 3 Resolution: 0.2mm...

Tevo Tornado Oversized Control Box (3 versions)
thingiverse

I intended to place a small tool holder there for the various bits and parts (glues, Allen keys, etc.) but I left it open for each one to insert whatever is most useful for them. Regarding the rear part: The rear is designed to hold an MKS Gen L or...

Ghostbusters Leg Hose Connector for use with Harbor Freight Magnet
prusaprinters

I had extra magnets so I used a screwdriver to pry one out of the metal holder and super glued it to the back of the washer. This greatly increased the strength of the pull before it can pop off.</p> <p>Third, the plug on the end of the hose that...

Filling machine "Hanimandl"
prusaprinters

The holder for the servo motor is firmly connected to the squeeze tap. Control unitAll operating elements and the corresponding microcontroller with display are located in the control unit. The housing consists of an upper part and a lower part,...

Hexagonal LED FPV Drone Gate
thingiverse

The joints were printed with PLA+ (any color, I used white), and the stand and circuit box holder can be printed with either PLA+ or PETG (I used black PLA+). Supports are not needed for the base or joints, the WLED control box only needs...

Cobblebot Vanguard Replacement Parts VOS
thingiverse

Update 21.12.2015: Added a replacement part for spool holder as it turned out that the first version had too much rolling resistance and didn't work well. The new design uses ball bearings for smooth rolling. The spool width can be adjusted as...

Compact Ball Mill
thingiverse

Assemble the position of the rubber bushings and bearings on the threaded rods and adjust until the vertical bearing holder plates are 203mm from eachother from outside edge to outside edge when the rod bearings are pressed into the recess. Make...

Large Bender Articulated
thingiverse

I replaced the pegs with metal ones by cutting some of the door plastic (with a spring under the bottom one to let me slide the door in) Recommended supplies White and black acrilic paint and tape (I used electrical) for the mouth and pupils...

MendelMax Vertical X Axis Ends & Carriage
thingiverse

Attribution I used: the "roundedRect" OpenSCAD module by WilliamAAdams the excellent zip-tie LM8UU bearing holder by skarab I've added them as remixes on the side and attributed them in the included source code for the parts. You'll need skarab's...

4th Gen Toyota 4Runner (2003-2009) | Wireless Charging
prusaprinters

This is to ensure the tray does not slide around and to provide the proper 6mm offset from the front so the lid of the center console closes without force or the need to adjust the tray each time. This design also takes the tissue box holder into...

Front Belt Tensioner Vcore 3 retro fit
prusaprinters

Leave +/- 2 mm of room between the idler holder and the frame. Repeat step 1 to 15 for the right hand side.When left and right hand side are ready adjust the belt tension with the M6x45mm hexagon screws to the proper value. Take care the M6...

Anycubic Predator Lighting ring Neopixel project.
thingiverse

: https://www.amazon.co.uk/gp/product/B07LG6RK7L/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 First thing to do is print the mounting plates and the LED ring holder. See printing instructions. While this is going on if you have another printer,...

Ultimaker 3 - Remote Shutter Timelapse Kit
cults3d

Just find and print a holder for it and glue it to the 3-axis mount. The Printhead mount: I designed a very sturdy mount to the Ultimaker 3 printhead. You can print it without supports and screw it to the printhead. To soften the touch between the...

TS100 18V kit / Makita / Bosch with folding support
thingiverse

(I have countersunk the base of the holder but hex heads are fine) • 4x M4 nuts – I use M4 Stainless steel as the hex cut-outs in the clips are designed for them. • Brand specific terminal adapter plate (See part numbers above) • 2x right angle spade...

18\20cm Motorized Turntable
prusaprinters

The surface the table is sitting on is also important here, so the bearing holders don't get blown out the back.You need a very flat print-bed for this. Otherwise you can get wobble on the table, or skipping gears. It is possible to do sort of a...

Stable and waterproof / watertight OpenSCAD customizer case / box / enclosure by pbtec
prusaprinters

For large cases add addtional ones in the middle of both x and y sides if neededUse several predefined wall mount holder, some with multiple mounting holes (up to 3)Important!If you use standard nuts you need to pause the printer a certain level to...

Dumbpad - 4x4 Macro Keypad with Rotary Encoder
thingiverse

On the 'Large' version I used [Red LED assemblies from radioshack](https://www.radioshack.com/products/12v-led-assembly-with-6mm-holder-red?variant=20332063173) I have a silly amount of old radioshack stuff..... 4. Diodes: In1's from...