rc snow tracks 3d models

I created this track adapter so my son could connect our old blue-area tracks with his newer RC train's tracks, which also work for 9V tracks. I built the adapter so he can play with all his trains on the same track system. To make the track...

A snowman, crafted from snow, is an iconic winter symbol.

Snow falls heavily outside on MCAD's second floor at night.

This is a unique, handcrafted snow effect tile that adds a touch of winter wonder to any design project. ...A single version of the tile is provided at a high resolution of 512x512 pixels, saved in the widely supported TGA file format.

https://youtu.be/EHVfCp5kPXc

Parts required: Rubber tracks - 4 pieces https://www.aliexpress.com/item/Remote-Control-Racing-Car-Tracked-Wheel-Tire-Front-Rear-Climbing-Off-road-DIY-Chassis-Tracker-for/32899304910.html?spm=a2g0s.9042311.0.0.27424c4ddEQLlO Central bearings - 8...

Full detailed model of the Komatsu PC228us-11 with original scale of 1:16. ... Fully printable in PLA or ABS for your RC excavator project. ALL FILES ARE NOT FOR COMMERCIAL USE. ... For a commercial license contact us.

Instructions: printed on Mendel - Afterward, submerge the tracks in scalding hot water; subsequently snap them together while gripping firmly with pliers and let cool afterwards. Not suited for high-speed racing but perfect for leisurely yard...

The design was sparked by P4man's inventive work on Thingiverse. It's mainly geared for rugged terrain, yet its bigger footprint gives it better traction on paved roads. ...Little supporting structure is needed during the printing process.

In the IV2016 format, this model includes iMates and features part numbers following Bricklink convention. For accurate loop and parallel functionality, the design is mathematically correct; however, data limitations may affect certain features'...

front or rear mattracks adapter https://www.youtube.com/watch?v=jh6WihC1Zgg

track link

!4 mm drive wheel modified for Arrma Bigrock and other 3s 14mm wheel hub size

History12.01.2024Front adapter updated (SMax_-_Front_2.0.stl). ...Changed mount framr ange to +0.5 degree.Print settings100% infillno supportsStrongly recommend to print with FLEX or TPU Hard (60D).

This is a concept for a drifting machine specially designed for snow. ...It's a mix of a Drift trike and a motor tiller.

This is snowy wheels for VRX Spirit / FTX Vantage / Quanum Vandal 4WD buggy. ...It has 12mm hex mount and 4mm shaft in diameter. Are you ready for the snow? Here is my album with actual rc photo https://vk.com/album-213358648_284506464

I crafted the frame template based on Timogiles' design and modified it for use with a CNC milling machine. ...Virtually every component is constructed from aluminum, while the rubber tracks are sourced from RC4WD's Predator range.

This is snow shield, it helps running on the deep snow, it do not allow buggy to dig deeply in the snow and helps glide on snow surface. It have three mount points, two points are at stock bumper, and third one on the tower. After printing you need...

Hi, I designed these tires for my little rc car to use on sand or snow, using pla flex filament. The design is optimized specifically for a 0.4mm nozzle (note: it's impossible to print with any other nozzle size except 0.2mm). I've added the center...

3D printable snow tires forany 1/10 scale car with 12mm hex on the wheel mounts. (and enoght clearance for the big wheels 110mm) I put them on my cheap nitro buggy and it worked great... at least when the snow wasn't that deep. In deep snow it...

This is snowy wheels for VRX Spirit / FTX Vantage / Quanum Vandal 4WD buggy. ...It has 12mm hex mount and 4mm shaft in diameter. Are you ready for the snow?

In deep snow it didn't have enough power to keep itself qoing.Check out the video to see them in action: https://www.youtube.com/watch?v=N8hnGQbgvMMPrinted with a 1mm nozzle for fast print times (under an hour each)Print...

This is Curiosity like snow wheels for Quanum Vandal / VRX Spirit / FTX Vantage 4WD buggy. It has 12mm internal hex, 4mm hole for the shaft and should fit a hub with at least 15mm protrusion. They are 11.7cm in diameter and 8cm in width. It is...

This is Curiosity like snow wheels for Quanum Vandal / VRX Spirit / FTX Vantage 4WD buggy. It has 12mm internal hex, 4mm hole for the shaft and should fit a hub with at least 15mm protrusion. They are 11.7cm in diameter and 8cm in width. It is...

These tires are specifically designed for use on a 1:10 scale RC vehicle. They feature an outside diameter of 110mm, making them perfectly sized for this type of vehicle. ...Furthermore, the internal hex is designed to fit snugly with the 12mm hex found...

Cat 349 1:14 model suitable for FDM Printing for RC projects. No internal mechanisms or motor mounts included in the files. Base and tracks are not included too. You can buy the bucket separately from this link...

The goal is to make a plow easy to print, reliable and also low cost.Every comments and suggestion is highly appreciate.

These wheels were designed specifically around my Traxxas Slash 2WD model. To complement these, I created a set of small skis for the front of the 2WD Slash. Along with these wheels, I also designed a set of front skis that work seamlessly together.

I've been using these skis with my Traxxas Slash 2WD, and they're specifically engineered for 12mm hex and 4mm axle shafts. I've also designed a set of rear wheels that complement them perfectly. Update: Many people have asked for the right ski...

I merged those two into one cohesive statement to suit my miniature scale Tamiya buggy perfectly. ...I advise scaling it up by a tiny bit, just 1-2%, because the hexagonal holes are really tight.