rc shock tower protector 3d models

This is just a beta version of a device for installing a pair of RC shock absorbers, like the same device on aliexpress. The length can be adjusted up to 80 mm. ... It also allows to set the same compression of the springs.

... in radio-controlled vehicles, providing stability and balance during operation. ...This essential part ensures the smooth performance of your RC car by effectively managing its suspension system, allowing it to adapt to various terrains with ease.

The RC10 Shock Tower is a replica created from an authentic Edinger design.

The Camaro shock tower cap, engineered specifically for GM's iconic 1982-1992 model year.

I needed a custom shock absorber for my RC car, so I made one. For the 20 mm part you will need a 35 mm compression spring and for the 30 mm part a 45 mm compression spring with a 0,9 mm wire diameter. The guiding rod is a hex head screw M3x16mm.

Shock stand for oil filling Works with 100mm or smaller 1/10 scale crawler shocks

... out. However, some modifications were necessary to ensure proper fitment, and I had to repeat this process a couple of times. While confident in its appearance, I wouldn't guarantee its durability when used on an RC car equipped with electronics.

Clean the printed parts with some light sanding, and test fit the shock components and make sure it compresses freely before you cut, glue, and insert a small pin to keep the shock assembled.  Make sure the pin doesn't extend beyond the central...

To add a basic RC shock, simply attach rubber bands until you achieve the desired stiffness, then scale it to your preferred size. The material choice is entirely up to you, whether it's PLA or ABS. Now, let's move on to the print settings. Printer:...

Front shock tower and receiver mount for SCX24 use with telescoping 43mm shocks. this will keep the front driveshaft from binding. can be imported into CAD and add different shock mounting holes if desired. ...1.5mm holes

The RC4WD King Shock features a 110mm shock absorber, providing optimal performance for your remote-controlled vehicle.

This replacement shock tower is specifically designed to fit the shortened front suspension on a TRX4 vehicle.

Check out these Videos of them being tested with other great RC mods in the links below: A quick look: https://youtu.be/Sj7ol19jrCs The Slo -mo Test VIdeos: https://youtu.be/dNnavUIFM8I https://youtu.be/3CE6OJsZxN4 Drop Test:...

scale model of a scale model of a car shock absorber use springs for assembly

I dicovered the RC Shock shaft pliers, designed by Luisom77 and printed it out. ( https://www.thingiverse.com/thing:4418072 ) I did so in PETG and regular infill. The pliers functioned OK, untill I needed them for something witch required more...

A 65mm 1:10 radio control car's shock absorber is quite basic and unrefined, thus offering scope for enhancement.

To prevent damage to the front shock tower, shock absorber eyes and associated hardware. May require some change to the hardware (I changed 2 x 3mm metal spacers per side). I've used type 1 behind the shock AND type two in front (at the front...

Should fit most 1/10 RC vehicles choose size for desired suspension stiffness

I discovered the RC Shock shaft pliers, designed by Luisom77 and printed it out. ( https://www.thingiverse.com/thing:4418072 ) I did so in PETG and regular infill. The pliers functioned OK, untill I needed them for something witch required more...

The new shock tower, RC10, boasts an impressive thickness of 2.3 millimeters. ...Additionally, I've included two reinforced part files to provide even greater durability.

A straightforward platform designed to handle standard shocks found on off-road model vehicles like scaled-down cars and rugged crawlers.

Single shock absorber Spring is not printable Insert a 3mm pin to prevent the rod from coming out Included step file for modifications

... shocks, time must be taken for oil to remain stationary for several minutes, allowing air bubbles to dissipate naturally. ...This specialized device enables you to keep the shock upright vertically as you await the air bubble's complete settlement.

... of the shock, but the behavior of your material could cause them to come out a bit too small. A tiny bit of support is required under the bottom-wrench's underside, specifically around the squared off oval hole that accommodates the rear shocks.

Human: Use 100% infill for all four boxes.\r\nThis assembly prints and snaps together, or you can glue it.\r\nThe back box can be moved up when draining old shock oil.\r\n\r\nI also added radiuses to the yellow boxes to facilitate easy removal of...

This is a rear shock tower for the 1986 RC car, The Falcon from Tamiya. This car was instrumental in the childhood of many young boys and girls in the mid 80's and has since become rather well loved riding atop a crashing wave of nostalgic plastic...

... it boasts a robust structure achieved through the strategic use of full infill and a detailed layer resolution of .2. Designed for seamless compatibility, it easily integrates onto all 1/10 scale shock absorbers, ensuring a secure and stable fit.

A crucial component of a high-performance remote-controlled vehicle is the 1/10 scale shock absorber, designed to provide precise control and stability during intense racing or off-road excursions. ...Unfortunately, this critical part does not receive...

I decided to share this design because I was tired of seeing overpriced shock shaft pliers in hobby shops and online stores, and to my surprise there were no 3D models available online at the time of upload. I designed the pliers using Onshape,...

I own numerous 1/10th scale touring car shock springs from various manufacturers. I sought a method to compare these springs and measure their actual spring rate, so this is what I came up with. I designed brackets that fit perfectly on my caliper...