rc sailboat 3d models

RC sailboat that really works. Designed on tinkercad. It can actually drive in the water too. Also kind of a work in progress. ...it has its own support.

The RC Sailboat's Hatch Features an Integral Eyelet Beneath for Securing a Rubber Cord. ...To Ensure a Tight Seal, Additional Gasket Material Must Be Applied.

Project Sailboat Under 3D Printing

... and the electronics. Features: Removable Keel Interior Water Pump Navigation Lights Motorized Propulsion Precision Control over Sails Video Link: https://www.youtube.com/watch?v=wqHZCgpKhl8 GrabCAD Link: https://grabcad.com/library/model-sailboat-1

trimaran rc sailboat

3D printed canoopy and keel Pb ballast forming equipment.Based on plans of Maxximus 1m RC Sailboat from the internet.

Parameterized RC Sailboat Bowsie with Recessed Knot Well Select Width, Thickness, Through Hole Size, Knot Hole Size, Knot Well Size Note: Length = 2.6 * Width

This is a gooseneck for a RC sailboat.It can replace the DF95 Gooseneck.You will need 4M screws and two (2) 6mm x 13mm x 5 mm bearings.In this video, you'll find the instructions to for the assembly :...

Here's a cap I built for the electronics hole in my RC sailboat's hull. It's engineered to keep water out and provides a secure fit with its bayonet coupling, locking it on tight. The concept behind this design was to give my boat a look that's...

This is a custom-made cap designed for the electronics hole in my rc sailboat's hull. It effectively keeps water out and ensures a secure, tight fit using a bayonet coupling. I created this cap to give my sailboat a sleek, racing boat-like...

The sailboat uses the ballast bulb from the CR-914 class rc sailboat. This is a somewhat challenging build, I would recommend understanding how to Glass a surface with carbon fiber cloth and epoxy, 3D printing (obviously), glueing (Super Glue, 30min...

Here is my RC RG65 Sailboat with a custom Keel featuring a horizontal stabilizer that I designed and 3D printed using PLA. However, I recommend using a slightly stronger and more flexible material than PLA to achieve the desired level of flexibility....

RC Sailboat Enthusiasts Connect Jumper Spreader Attachments Directly to Masts Using Lightweight Carbon Fiber Strands Soaked in Epoxy Resin.

Handrail stanchion base for Kyosho Fairwind RC sailboat. Can be resized for other uses. ...Center hole 2.6mm.

Drawing template to identify rigs on RC sailboats, letter height 20mm.i haven't find one so I made it. ...I use for RG65 class.

I've engineered it to serve as a prototype, but you can also create a static model from it. The underside of the hull boasts an improved design that enables better cutting through water than its real-life counterpart. The sail only needs to be...

This is a tackle ( a traveler ) for rigging/cordage/ropes of rc sailboat. ... This particular design is developed for RC boat M class but it is also perfect for al classes ( IOM/Star/AC75 ) and all mast arrangement (main sail, genoa, jib etc etc...)

This box complies with the rules of Footy class Rc sailboat.The rule You can find here: https://footy.rcsailing.net/rules.phpIf You design or just build a Footy it is a useful tool to check out if Your boat fits the rules.I think the biggest...

This is a custom-designed rudder that can be easily adapted to suit the specific needs of a large radio-controlled sailboat. ...Simply modify the provided SolidWorks file to ensure a precise fit on your unique vessel.

The boat is challenging to control due to a lack of experience with RC yachting; any advice would be appreciated. The design is created using Fusion 360, and I can share the files upon request. The current hull is a simple design created in Fusion...

The sailboat weighs approximately 900 grams with a DF65 bulb installed. It can be printed as a single-layer spiral vase hull in 0.55 mm wall thickness. The three-section hull features stern and midship sections measuring around 200 mm high, while...

All printed with PLA+, except: 1 x HOTRC-HT-6A Radio transmitter with FHSS 6CH receiver 2 x GDW DS041MG-Micro Servo 1 m 6 mm aluminium rod for the mast (550 mm) and the boom (260 mm) A piece of lightweight spinnaker cloth for the sail 4 AAA battery...

[Homepage]https://www.schluppeck.de/2020/10/rc-segeln-boje-3d-druck.html) Cover 0.2 mm layer height 5 floor layers / wall layers / ceiling layers 50 % Infil float, tripod, tip 0.2 mm layer height 5 floor layers / wall layers / ceiling layers 5 %...

If you want to build your own Sails and rigging system for your Rc Sailboat, these designs are for you. ...You can find plans here : https://dfracing.world/df95-boom-drawings-mast-lengths/ I used 4-6mm carbon fiber rods for the booms and 6-8 for the...

This is a bumper for an EC-12 RC Sailboat. I didn't like the fit the one I found for sale and I also wanted something a little meaner looking. This one is printed with flexible TPU filament and has a fairly snug fit. I know it works because I had a...

This is a ballast carrier for the Alioth IOM 3d printed RC Sailboat. It could be modified to fit other boats. It provides a simple way to carry brass ballast rods and also helps reinforce the keel area. These two brass rods are about 1-1/4”...

Perfect for 3d printed (lead casting) rc sailboat bulb. Thingiverse is missing archive or directory upload - not appropriate for openSCAD. Please take the complete source from my GITHUB: <a...

Spare bowsies for our RC boat "Compass" Might be necessary to rework the bores by a 1mm drill after printing

This is a control arm for the rudder assembly for the RC schooner Annie, from http://www.bearospaceindustries.com/boats2.html. It is properly sized for use with the control arm included with the rudder servo specified in the plans. Printed of PLA...

This is a remix of a great project from Thingiverse: rc katamaran sailboat made by PrinzThomas. The original hull files were too large for my printer, so I split them into eight parts to make it printable on smaller machines. Print Settings: ...