rc roof rack 3d models

A fast and easy-to-assemble roof rack system that's compatible with 4 high-intensity LEDs rated at 5 millimeters, complete with cleverly designed printing support that requires some tricky adjustments to get just right.\r\n\r\nThis handy rooftop...

This is an extra component meant to go along with a T5 roof rack holder system. Sometimes, printing this part can get tricky due to its design and supports. ...To assemble the complete product, you will also need to obtain another part from Thingiverse...

I lost one of the plastic roof rack clips from my Kia Ceed, so I created and manufactured one myself! It looks almost identical to the original but is close enough for anyone who doesn't know what to look at. Did its job flawlessly. ...Print Settings...

I Designed this part after a friend of mine broke the roof rack component. It was manufactured and thoroughly tested. A related item can be found at https://www.thingiverse.com/thing:2796184. Printing Settings: Printer: K8400. Rafts: None. Supports:...

Simple spare parts for car roof racks or carriers from Hakr. Use at your own risk. They are designed to be easy to install and remove, but the manufacturer disclaims any responsibility for their use. ...The frame is slightly reinforced, while the base...

This model shows a replica of the plastic part that secures the 8mm nut in my Rola roof rack cross bar (Model 59834, APE series - I'm unsure if similar crossbars from other Rola racks use the same component). The low-cost stainless bolts provided...

Helps to keep out the mud and the muck. Designed for a 2019 Outback roof rack but may fit other years & Subaru models ; Impreza, Legacy , Forester , etc. Print Settings Printer: Eryone Rafts: No Supports: No Resolution: .2 Infill: 20 %...

I designed this Roof Rack for A Hard Body D90 to break down into sections, making it simpler to assemble and disassemble if something goes wrong. It requires 22 - 1.5mm bolts, which are also used in the lock-on wheels. ...I printed the netting in a...

The plastic piece in my Rola roof rack cross bar model 59834 (APE series) holds a 8mm nut. The supplied stainless bolts had burrs that made installation difficult and rounded the nut trap. I printed an ABS replacement with 50% infill, .2mm layer...

... motion. In the past, a Yakima roof rack with gunwale brackets amazed me with its improvement. ...For installation, print 4 copies of the sizing template, slide onto the tubes, adjust to fit your canoe, and tighten for secure transportation.

Not sure what car roof rack this belongs to. If I remember to find the make/model, I'll post it here. The stock end caps are made from a soft plastic (not as soft as TPU) which splits in half due to creep or something. These fit on snugly...

Not sure what car roof rack this belongs to. If I remember to find the make/model, I'll post it here.</p> <p>The stock end caps are made from a soft plastic (not as soft as TPU) which splits in half due to creep or something.</p> <p>These fit on...

In accordance with the non-commercial clause of this license, if you produce this part (Gen 8 Roof Rack.STL) for others, you may not receive more than $1.50 per part plus shipping costs. ...This amount is based on an average estimate of material cost...

UMG Unimog axilal, tamiya roof basket

My classroom is equipped with Makeblock mBots, so I took the initiative to design a roof rack. The holes are spaced 16mm apart, which is standard for all Makeblock parts. I'm open to modifying this design in any way needed. Currently, I'm...

Needed a key to unlock/lock the OEM roof racks to unmount/mount them on a 2014 Toyota Rav4 XLE. The only way to get a key was to order one from the manufacturer. Printing it was a lot cheaper. The key is just an embossed elliptical shape on a...

Designed to minimize turbulence and associated noise on tubular roof racks, this innovative creation gets to work. Built for a 30mm tube diameter, its versatility allows it to be scaled to any size requirement. Measuring in at 25 cm in length, the...

I lost one of the plastic roof rack clips from my Kia Ceed, so I made designed and printed one myself! It doesn't look exactly the same but it's close enough for the untrained eye. ...Did the job perfectly.</p> <h3>Print instructions</h3><h3>Category:...

took edwardchews c-14 roofrack and resized it for the d12 and designed some roof mounts.

--- V1: A slight remodel/remix of the "EMT Roof Rack Tower"; I ended up widening the pole support to use 1" (ID) electrical conduit, removed the bevel for a better print experience, added indents for the rivnut edge, and smooth a few sharp edges. ...

You can see how this looks in the PrusaSlicer photo in which one support has the perimeters increased. V1: A slight remodel/remix of the "EMT Roof Rack Tower"; I ended up widening the pole support to use 1" (ID) electrical conduit, removed the bevel...

Easily secure your bike with a swift click thanks to the quick-release feature and two U-bolts. ...Attach it effortlessly to roofracks or roof bars by simply clamping the fork onto the lathe section, using a 30mm roundbar for stability.

My ski box sits even with the bottom of the crossbars, so I designed the pylons high enough so that even if someone opens the moon roof, it will not interfere with the ski box. Other crossbars could be used, but you might have to modify the upper...

A roof rack for Farmersmark's 1:10 offroad trailer Print uppside down, no support needed Use glue or drill holes and screw

Printed at 100% infill with PLA. ... Parts to make a rack to store RC airplanes. ... Using 1in and 2in PVC tubing.

RC car pinion rack. ...Need to drill holes to open the rest of the way and insert nails cut down as the steel lins.

This is a compact and understated spare tire rack for an RC car. A 4mm bolt and nut secure the tire in place, utilizing simplicity with a wing nut that necessitated a spacer to prevent interference from the wheel's bolts. To enhance the original...

RC GANG 93 Roof rack for lexan body of COMBI T1 VOLKSWAGEN brand TAMIYA 155x125x50

This is a 1/10 scale alignment rack / setup station, designed for rc drift cars. it allows precise tuning changes of: Toe: -40 - +40 degrees Caster: -20 - +20 degrees Camber: -15 - +15 degrees It can also be used to help set ackerman and visualize...

this is a rc hanger I designed to hang RC's on the wall. It works for 1/20 to 1/5 scale RC's. The rod(16mm) can slide out so that more hooks can be added. You will need 1x M5 nut and bolt per hook. ... An open and closed rod end is added to insert more...