rc model zeppelin

IntroductionThis model provides an effective, low-cost teleprompter for livestreaming and recording. Using a Raspberry Pi and Pi Camera (the cheap, non-HQ one provides great full-HD video in this application), your phone to display your script or...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

All in all, I believe your satisfaction with this mask should be limited only by the skill with which you make it, and not by any features of the design.Hope I won’t see any more comments to this design base on general 3d print issues(rough surface,...

Dimensions: 510 m × 330 m × 241 m Model scale: 1:3x103 (15cm) 1:8x103 (7cm) References "Lawrence, K. and Benner, L., Radar shape models of asteroids compiled by Lawrence V1.0. urn:nasa:pds:gbo.ast.jpl.radar.shape_models::1.0. ...NASA Planetary Data...

 A lot of my models are designed for the 2.49mm walls that equate to 6 print lines with a 0.4mm nozzle.  </p><p>Both the Tool Holders and the main Jig are setup to have a color transition at Z height. ... </p><h3>Donations</h3><p>If you found this print...

Designed with the help of acoustic modelling software. Comes with carbon fiber slide, complete with PLA stockings.</p> <p>Also available in large bore version at <a...

This should be the first unit from the power supply mob unit -&gt; this contains just leds and has 2 holes in the bottom for an input line and output line end cap unit -&gt; this contains just leds and has a single input line hole in the bottom The...

 A side note - you also probably should be using my rear PC4m10 jack for your MMU3 https://www.printables.com/model/542409-mmu3-pc4m10-rear-connector The perfect length is one make an even curve downward and the up into the back of the MMU that is...

35mm diameter)Electric cablesElectric soldering iron and solderAn M4 screw with its corresponding nut (approximately 15mm in length)Two appropriate screws for fixing the DC motor to its support (depends on the type chosen)Instant glueStep 1: Print...

As per my usual, each Zip file will contain the model un-based, based, and with supports. In order to keep files sizes down, I will no longer included the mirrored files for some of the linemen which you can easily do yourself in either the Chitubox...

Able to hold 1 stack of cards and 2 columns of hexes. --4-2-17-- Added player card 2.2, a little bit smaller on the separator pieces that come off the model, should be easier to fit in the box. --4-2-17-- Removed older hex and cards .stls and...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Take a look at the pictures to see the specific model What and how many do I print? For a set of 8 (Including feet) (Excluding elbows) x5 Body x3 Lids x2 Thigh Lids x1 Guide x2 Hip clips x3 Aux body x3 Aux Lid (of your choice. I personally...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

If you have a printer, then you have such electronics! PaScn3D connection to Prusa 3D printer in a minute (tested!) – dedicated mounting brackets, components adapted to the dimensions of the device Modularity – adaptation to other printers without...

I got a package of 5 and when I opened them I found that the design had changed slightly and the material they used on the newer models was slightly thinner. The original clips were therefore a little sloppy. I adjusted the clips to fit the newer...

Thus I found my way to thingiverse and sought for every model that was irregular eventually finding some customizable builders. While the brick making one is heavy, beam kind was cool, but limited to either halfheight simple or up to # shape with...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

- You can find a somewhat more detailed list of supplies in my Instructable: https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Any combination will do (as long as the driver is 4" or smaller so it fits the enclosure -...

Knob channel.stl - channel knob, for 16 position rotary encoder, model unknown, mine was from professional 16-ch radio. 7. Antenna.stl - old-style, PRR mock antenna. 8. Antenna New.stl - new style, EZ-PRR mock antenna. 9. PTT Lemo Single.stl - PTT...

This is a model and instructions for how to build your own fiber optic light engine that is smart and can be controlled through google home. This version uses a smart LED light bulb as the source of light. It can use any smart light bulb that is...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

This model includes both a solid and a honeycomb version whether you want to print a more authentic and traditional version of the warlock or if you want it to be more unique.&nbsp;I used absolutely bottom of the barrel parts to get this to a fully...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Please review the filenames, model file comments, and pictures before starting.Non-printable parts and necessary tools:The clock movement and clock second...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

If desired you can secure it in place with a sticky pad or some hot glue. Push the insert into place. Lower the NeoPixel Ring into place, ensuring to route the wires through the slots in insert. If you are using a diffuser, place it on top of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

Special credit goes to Orcy Wagh, who created the servo model over on Grabcad (https://grabcad.com/library/micro-linear-servo-right-1). What is different? In contrast to the BFPTouch, this thingy uses a nano sized linear servo to release / lock the...