rc model stand

I already had some Koss Porta Pros so I printed it and used that for a couple of weeks (after tweaking the size of some parts for a tighter fit, especially the push pin which is/was modelled too small). However, after a couple of weeks using that,...

Legal notes 3D printable file and models ©2024 Bethesda Softworks LLC, a ZeniMax Media company. All Rights Reserved. This is an STL ONLY for 3D printing and not a physical product. Requires a 3D printer and knowledge of 3D printing to use STL files...

Carefully tipping the rocket body to allow the superglue to dry and smooth out.Repeat this process until all 3 fins are in place.  Producing the launch guide When launching a model rocket from a standard launch platform a 3.5mm guide...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

The following adapter will fit "QNINE M.2 SSD Adapter to 2.5" SATA 3" Amazon.de https://www.amazon.de/QNINE-basierter-Schl%C3%BCssel-Unterst%C3%BCtzung-Festplatte/dp/B07RGT79WQ Amazon.com...

and using less material) The idea is to print the markers in a different colour using the "Filament change" script (under Cura, M600 gcode, if supporter on your printer); you may also use the standard rotor-cover.stl if not interested by this version...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

...You can also save money if you can find a local shop that sells a retina display replacement, But be sure it's the right model. All in all you could maybe save 50~100$ depending on the parts you already own and your own creativity in sourcing parts.

As such, some knowledge of manipulating 3D models will be required in order to make use of these. Since I created them, decided may as well share in case someone else can use them. You can see the principal that allows these masks to work in...

Print Settings Printer: FlashForge Rafts: No Supports: No Resolution: .2mm (Medium) Infill: 20% Doesn't matter Notes: For the most part, I intended these to print without supports; however, the housing is so wiggly that it needed some once I...

Most LEDLB, LEDP10W and LED10W series lights ship with mating connector as part of a harness or pigtail, depending on the model. Some larger LED lights like the LEDLB-160X2 or LEDLB-200X2 or multiple function LED lights (i.e. ...high/low beam,...

This + rotating the model upside down let's me print the whole thing with no support at all - my print time was 2h 39m and I used small, low-density raft, just in case. https://www.thingiverse.com/thing:4565091 Another thing - it appears that the...

... differences. As always please share any thoughts or feedback for further discussion and help each other move forward in design solutions, modifications for use on 3d printers like this model. ...These files were originally made with Tinkercad too.

The model isn't geometrically perfect as I did the scaling in blender (The only editor I know how to use), but it works which to me is the most important thing. You will need a couple screws to put it together as the ones which come with the...

Wled ist eine Opensource Software von Aircookie, schaue hier : https://github.com/Aircoookie/WLED Du brauchst dafür die Lampe, die gedruckten Teile: 1x Deckel 1x Fuß Gibt es hier zum Doownload: https://cults3d.com/de/modell-3d/haus/test-leon75 Ein...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

A .3mf file and pre-sliced .bgcode file is available along with the STL models. Also prints well on a Bambu Lab P1S.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it...

I'm no design expert, and 3D modelling makes my brain hurt. However, with a lot of perseverance, a set of calipers, hundreds of edits and redesigns, dozens of test prints, I have made a replacement ring battery. You will need the following: *...

Five basic shapes are available as elements:pieces with straight ends, adapters with either two plugs or two sockets, T-shapes, L-shapes cross-shapesTo make your own drawer partition, make a sketch like the image below, calculate...

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

For fixing of the coil, the trickiest part of this build, having it only glued on the stepper shaft is not enough, it must be compressed axially, otherwise, it will "uncoil" and break on pushing or retracting the filament (depending on the direction...

For me it wasn't a problem, but I've added a bit of chamfer to the bottom for a bit of extra movement. If you manage to make a square 16x16mm glass then I've included a 16x16 model without the bottom portion that should not limit the camera...

The only sound comes from the layer fan.I have included the STEP files to facilitate remixes and alternative configurations.An associated BMG type extruder/carriage can be found here:...

rice or sand.Glue if the press fits are not tight enough Testing tolerancesStart by printing the models press_tolerance_test and rotation_tolerance_test from the folder Common parts.Press fit toleranceUse the press fit test to decide which press fit...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to...

Some of these items can probably be changed for cheaper or better alternatives, but these are the exact elements I used: Main Components + [Raspberry Pi 4 Model...

Failing that, just send me a message and I can make one that's the appropriate size.To-Do (Notes for Myself)This is an evolving project I'm using to re-learn CAD modeling, so I'm adding a list of things I'd like to tackle for my own reference...

The only models where the current orientation is not necessarily the recommended one are: Duct, DripVat & Bottle Some files are available with supports. I cannot guarantee in any way that these supports will be strong enough for your printer to...

Now it measures all points in Bed UPDATE Sept 29th Activated MPC Autotune for Nozzle https://marlinfw.org/docs/features/model_predictive_control.html. If you don't want to use it, the previous version is with PID Autotune, just don't update it</h3> ...