rc jet turbine 3d models

so i downloaded and printed openz cars from rockracer, garuo3d, byebyeracing, and "make it rc". then took the chassis that i had the most stuff that fit and modified till i was happy. several test cars and broken pieces later and this is V1. i...

In 3d printing a RC Stearman model I needed an 11x5.5 prop. Instead of paying $3 for one I spent<i>thousands</i> of person-hours using high-expertise design skills to build this!</p><p>It's a<i>procedurally generated</i> propeller design...

I have been flying RC models and printing airplane models for years. Designing a  flying machine can be tricky. Should I enroll in a proper fluid mechanics? Not yet, I took the challenge to retrofit an existing balsa wood airplane model as a starting...

It is final, printed with PLA, no support, 20% infill. The Antenna Mount sits on the rear end of the quad, it has a hole for the VTX antenna, two RX antennas (90 degree), and it has a place to fit in a LED strip (Aurora RC, 25mm x 6 mm). It is final,...

### Notable Autostar configuration parameters Telescope - 4504/114EQ if FW patched, otherwise DS-127 Alt/Dec Ratio = -03.28533 (1:144 worm ratio) Az/RA Ratio = +03.28533 (1:144 worm ratio) Alt/Dec Percent = 75% Az/RA Percent = 75% ### Parts list 2x...

*Parts* [AXLE](https://www.thingiverse.com/thing:5538562) x2 [FRAME](https://www.thingiverse.com/thing:5539294) [CABIN](https://www.thingiverse.com/thing:5539225) [LOADER](https://www.thingiverse.com/thing:5540090)...

See it working here: https://youtu.be/nNygre-98G0 Motion is obtained from two RC servos whose arms are connected in a W shape. At the middle of the W sits a screw able to push the minutes arm via a pad. The minutes arm itself can push the hours arm...

I used this here: https://de.banggood.com/Remo-B5509-Ball-Bearings-593mm-For-1621-1625-1631-1635-1651-1655-RC-Vehicle-Models-p-1450586.html - 9x M3 30mm screws and nuts to conetc top and bottom trays - otionally: 9x M3 0.5mm washers to put between...

This being said, these are the parts/electronics: - ESP32 DevKitC (v1 or v4 tested) - PCA9685 16Ch Servodriver - 0,96" I2C OLED (SSD1306) - 2x HC-SR04 Ultrasonic-Sensors - GY-521 Gyro - HW-482 Relay (sometimes also as named KY-019) - ESP32-CAM with...

Next step is likely to be RC servo based flippers and some magnetic components.  The pink & yellow modules will contain micro switches for player controls.But for now these bits are incomplete.Solenoid LauncherI used solenoids out of ES2000 electric...

Any amount of support is greatly appreciated :-) paypal.me/BrianBrocken Feel free to take a look at my other designs: 3D printable antweight battlebot: Bulldog: https://www.thingiverse.com/thing:4623536 SpaceX inspired edf rocket:...

... the X axis rail. There's much more to say, but.... I'll let the pics do the rest of the talking. Thanks for viewing! And oh yeah, it prints SO nice too. I've added a couple pics of some RC airplane parts I'm printing from 3DLabPrint.com.

Any amount of support is greatly appreciated :-) paypal.me/BrianBrocken Feel free to take a look at my other designs: 3D printable antweight battlebot: Bulldog: https://www.thingiverse.com/thing:4623536 SpaceX inspired edf rocket:...

More informations https://www.rc-network.de/threads/andreas-delta.11822532/ https://www.rcgroups.com/forums/showthread.php?3754295-Andreas-Delta Specifications airfoil: NACA 0006 wing span: 1100 mm wing chord: 680/200 mm CoG: 460 mm from rear...

For any questions and assistance please use the RC-Group thread:https://www.rcgroups.com/forums/showthread.php?4036507-Curtiss-P-40-Warhawk-600-800mm-LW-PLA-%28L3D%29 PARTS LINKS X1 A2208 1400KV Brushless Out-Runner Motor (or suitable...

You can get the servo here: http://www.banggood.com/3_7g-Micro-Mini-Servo-For-RC-Model-p-77696.html The battery tray is at: http://www.thingiverse.com/thing:1289398. I have also included the battery tray files here. Make sure you print out the...

Or copy the design to your own workspace and modify as necessary.\r\n\r\nOne of the Onshape tabs shows a potential router spindle design using a brushless RC motor (MT Series 5206 320KV). This is very experimental, and it will be necessary to...

~/ edit rc.local to run inputs.py at startup. Follow this guide to add controller mappings to PPSSPP: https://retropie.org.uk/forum/topic/15577/ppsspp-controller-setup-guide-for-when-nothing-else-works Edit autoconfig for N64 emulators because...

This one is larger and has room for a 4S 14.4V LiPo RC battery inside. BIFRC_large_case_body.stl is the body by itself BIFRC_large_case_lid.stl is the lid by itself s2tIC8ndth.stl is both body and lid in one file The BIFRC is installed in...

The brain is an arduino uno, and the rfid module is a RC-522. The player plays music from a DFPlayer Mini that has a micro SD card. Watch the video! ... https://www.youtube.com/watch?v=5Y1Psf6igHE Step by Step instructions:...

The brain is an arduino uno, and the rfid module is a RC-522. ...The player plays music from a DFPlayer Mini that has a micro SD card.</p> <p>Watch the video!</p> <p> <figure class="media"> <oembed...

... the X axis rail. There is much more to say, but.... I'll let the pics do the rest of the talking. :-) Thanks for viewing! And oh yeah, it prints SO nice too. I've added a couple pics of some RC airplane parts I'm printing from 3DLabPrint.com.

Video can be found here: https://youtu.be/SAgiv4o8rxQ More info can be found here: https://hackaday.io/project/168301-arduino-controlled-photogrammetry-3d-scanner components used: 1 × 9g Servo motor link:...

If you're planning to do any traditional RC aircraft construction, this tool is almost a requirement. It can save you hours of cutting with a ruler, and ensures that your strips are parallel. My nearby hardware store is not fantastic, so it only...

Three RC Helicopter bearings (6x3x3 or 6x2.5x3) 5. One 450g weight 6. Eight coins - I'm overseas with foreign coinage, but quarters should work 7. Approximately three meters of string - I'm using 550 cord guts since that is all that I currently have...

Here is a hook that I designed that fits on my bumper :)\r\nhttps://www.thingiverse.com/thing:2830523\r\n\r\nAlso, user "Oldsu" has redesigned and upgraded the base part, and you can find it...

The foam cutter mount I remixed this from only worked with the old MPCNC.It is basically a combination of the mount for the DW660 spindle (https://www.thingiverse.com/thing:944952) and this foam cutter attachment...

Electronics 1x Bigtreetech SKR 1.3 mainboard 4x TMC 2208 Stepper driver 1x BTT TFT24 or BTT Mini12864 display 1x Mean Well LRS-150-12 Power supply 1x SSR Relay 8A - Hoymk SSR-D3808HK 1x 16mm anti-vandal power momentary switch - 110/220V variant 1x...

____________________________________________________________________ BetaFlight Tune: ``` set p_pitch = 100 set i_pitch = 50 set d_pitch = 70 set f_pitch = 125 set p_roll = 90 set i_roll = 45 set d_roll = 65 set f_roll = 125 set p_yaw = 65 set i_yaw...

"RC Ready" Hellcat Mini V1 This model is the result of another combined effort between (RonStG) (Aileron Ron) and myself (The3vilRoYcE), it's based on the original printable frame version posted last year, however there are some very significant...