rc felgen 3d models

Everything else shouldn't matter too much, personally, I'm using: - 3x NTM 2830 propdrive (KV is probs ~1200 too, I'm using old models), I'm running it on 3S with 11x4 props I think, 4S with smaller props also works, just listen to your RC forums -...

These are commonly available from Amazon and others, and are sometimes used as axles for small RC cars. Cut to length and sand the ends to allow smooth insertion. It will likely need a few light swats with a hammer. DO NOT BEND THE ROD as you are...

Please be aware that rc explorer dot se have a high power board being implemented for easier management with integration expected; watch expert build process videos from trusted industry sources like David himself for reference on precise assembling...

Repurpose your spare quadcopter or RC airplane parts to make this desktop solder fume extractor! Here it is in action: https://www.youtube.com/watch?v=VG0oGK6q3KU. I got fed up with solder fumes wafting up into my face, so I designed this fan to...

Uses a cheap light 9g servo to push the shutter button on top of the camera - you have to adjust the settings in your RC TX so the servo only moves just enough to press the button. Start out with the servo travel very low and slowly increase it until...

More infos on the customizer: https://www.udos3dworld.com/customizer.html More infos on the generator suite: https://www.udos3dworld.com/generator.html To get all the tools and start creating your individual models, become a patron now:...

http://rubber3dprinting.com/ http://palmiga.com/ Follow me on Instagram and/or twitter: http://instagram.com/rubber3dprinting https://twitter.com/rubber3dprint For more info regarding release of the F1 car and also the other Open-RC project head...

For example, this model can be optionally equipped with 3 servos to operate all functions by RC. All 5 axles are steerable if desired and can optionally be replaced by rigid axles. The axle swing arms are included with the data set. Thus, the...

The idler end required support material removal or drilling in the idler bolt hole, using two 5x10x4mm bearings, a 5x18mm bolt and nut for the idler, and optional .5mm spacers sourced from RC cars. ... Lastly, 3mm nuts and bolts clamped the z-support...

INTRODUCTIONThis is the front part of the body for the M548 RC 1/10 scale model. I have design it in order to be printed in a 200x200 mm printer (the most common). Everything is my own design exept the front lights which I have to thank to my friend...

Several outdoor tests were conducted with the robot assembled and complete with its RC module. You can watch these tests on YouTube by visiting: https://youtu.be/-VNqAblKKN0 https://youtu.be/oEGFaRnfMHc The Rocker Tubie DK-B (Developer Kit-Base)...

It also has worked very well at catching skunks which I don't alwayslike having in my trap.This is an automated door that opens on sunrise and lowers on sunset to preventthe night time creatures like skunks and possums from getting caught.I took a RC...

Assembly Video: https://youtu.be/GqohsdSTQrc Using **"2mm Male Female Banana Plug Connector for RC Model ESC Motor Speaker"** to convert Foster Connectors to electrical connectors -concentric BNC like. The printed parts hold these 2mm contacts in...

In addition to the printed pieces (less than four hours of print time and 32g plastic), this design requires the following: 3 x 20mm long 2mm shafts 1 x 30mm long 3mm shaft 2 x 6x2.5x3 RC helicopter bearings Here are links for the non-printed...

For those asking, this project requires a BIG motor - some of the biggest RC motors available or even EV type motors. This 88mm impeller is not a 50mm one; it's pushing pressures similar to commercial 20-30hp units, which also require power similar...

This is my custom spinner design for the 3DLabPrint Spitfire MkIX RC model aircraft. In my opinion, a well-designed spinner and propeller are crucial in achieving an authentic scale appearance of a model. Unfortunately, I was not satisfied with the...

FeaturesOptional compartment for a 350mAh LiPoly battery (with a zip-tie strain relief slot)Slot for a rare earth badge magnet (source provided)Support for Adafruit's stackable Feather wingsCable management and routing slotsUpside down board support...

A fishing trip was planned, and an RC boat would be ideal to play with while out on the lake. The necessary hardware wasn't available, so the boat was modified to fit a water pump. A newer version of that pump, modified by me, can be found here:...

For example, this model can be optionally equipped with 3 servos to operate all functions by RC. All 5 axles are steerable if desired and can optionally be replaced by rigid axles. The axle swing arms are included with the data set. Thus, the...

This proyect born as a attempt to create a rc plane with a good performance, predictable and gentle characteristics, resistant, easy to mantain- repair, like the real counterpart the noble Pilatus Turbo Porter. This airplane combine the foam...

As an added lock to prevent the blade from moving too freely, I used a clothespin typically found on RC cars. Next, insert 09-support into the shaft followed by 10-upper_pivot in its center. With that complete, you can now put in 12-rudder - apply...

... the amount of port-print sanding required. It might be possible to print this larger, and using the keel print to make a lead casting, make an RC sailing version. Do please post a make with pictures if you print this! ...I'd love to see them.

... RC controlled box would be really sick. autonomous driving creating a shelve out of multiple boxes Hardware store parts: The slim edge boards need to be cut 42mm shorter than the other boards. Width is 50mm. Recommended screws: spax 3x25 (20 pc.

... STL files for this project on Thingiverse at https://www.thingiverse.com/thing:4093868. If you're an RC enthusiast, I'd love to have you join our community! ...If you like this video, be sure to like it and subscribe to my channel for more content.

Tools required-Soldering iron-Heat shrink-LiPo Balance Charger (like the IMAX RC B3)WARNING WARNING WARNING WARNING WARNINGDo not charge a lipo battery in the original lead acid charger that was included with your device. You will burn your house...

As this model is in 1:10 scale, it is rc controllable and not a quick print!This is my second 1:10 scale “Lanz-Bulldog” tractor. Many parts are quite similar to my 1:10 scale “Eilbulldog” but I have optimized most of them. The interior is quite...

A few days later, on August 28, 2018, I rounded off the corners (in files with "RC" in the name) and slightly enlarged the magnet holes to prevent the print from breaking when installing the magnets. On September 5, 2018, I introduced a new...

You could basically use anything you want, like an RC-Remote or anything that can tell the ESC to spin the motor. Just for completion I added my Arduino code. I take no responsibility in it destroying something because it is slow. You can send it a...

The rc.local.txt file is for Octoprint installs, see the youtube video for details. Need more help building this? Want to discuss it? Want a custom mount for your setup? I can be found on my public discord chat server. Glad to answer any...

I won't be including instructions, as henryarnold provides a great PDF to follow already (and I also think that by looking at the photos and complete assembly file I've included, the construction is quite self-explanatory.To keep the servo wire out...