rc drift track 3d models

Saw some video of someone putting slicks / drifting tires on their rc car. Wanted to see if it was possible to 3d print these. As Im guessing they will wear out I wanted to make them changeable. The inner parts that "lock" together are made...

Here are the parts: WLToys 1/28 RC car with drift wheels/tires Standard towerpro style 9g servo Eachine ATX03 Runcam Nano Small 1s battery for video system All lights are 3mm LEDs; six in the rear and four in the front. Thanks for looking! *UPDATE...

Here are the parts I used: WLToys 1/28 RC car with drift wheels/tires Standard towerpro style 9g servo Eachine ATX03 Runcam Nano Small 1s battery for video system The lights (optional) are all 3mm LEDs, six in the rear and four in the front. I...

You must either swap gears in your transmission or reprogram your ESC to correct thisEDITS:1/26/24: Added multi-body STL for the yin/yang pinion pulley-----------------------------------------------------------------------------------Onshape Doc:...

Replacement Body for Amazon's 1/24 Scale Drift Cars Available Now Amazon users seeking a fresh RC car design can access a custom-made replacement body from various online sources. This innovative accessory is designed to upgrade any of the available...

This track is specifically designed for use with the RC Tank by Staind. It's a remix of my initial version of this printable track. This track is created to be printed in sections, minimizing the number of M3 bolts needed. I tried another track...

An assortment of connectable track barriers for mini RC vehicles, I sized these for Turbo Racing 1/76 RC cars. Would also work well with Kyosho DNano or Sturmkind Dr!ft. Remixed from Meistro's excellent little single barrier piece. I reduced the...

The original Tamiya tire fits perfectly on the TT01 TT01e. ...The tire's diameter is approximately 50mm. It uses a 12mm hex shaft for mounting. Or, for drifting, you can print the complete Drift Wheel.

... on slippery surfaces. ...Addon for the nice 1/76 RC racetrack design of robdeanhove for the cool littel Turbo Racing micro RC cars. ...https://www.thingiverse.com/thing:4762231Available in 4 different widths (in mm)Print with the chamfered side down.

... on slippery surfaces. ...Addon for the nice 1/76 RC racetrack design of robdeanhove for the cool littel Turbo Racing micro RC cars. ...https://www.thingiverse.com/thing:4762231Available in 4 different widths (in mm)Print with the chamfered side down.

My friend recently ordered a set of tracks for his RC from Wish.com, but unfortunately, they arrived 3D printed with subpar quality. I decided to save his purchase by reprinting and recreating the needed parts, so they'd be ready if he needs more in...

friend ordered a set of tracks for his RC off Wish.com, these little lockers came 3D Printed... and not such a great print was done so i opted in to save his purchase and not only reprint but recreate the parts needed and have them on stand by for...

I based this design on the "Mini Track Loader RC" from Zedpi. You can use the LEGO chain and other parts from Zedpi's design at https://www.thingiverse.com/thing:1000713, making it only slightly larger than the original one. The idea originated...

This is a remix of the cute RC Mini track loader from Zedpi. The Tower Pro SG90 servos are slightly larger than specified, requiring an extension of about 2mm to each side of the frame to accommodate them. As this project is still in progress and...

Check out this set of 3 custom ESC holders for you 1/10 scale drift car! Just screw them in and get drifting! ... These were made to fit Yokomo YD2 and MST RMX RTR chassis (as these are the only chassis I own), but you can easily customize it to fit...

I designed this based on the "Mini Track Loader RC" from Zedpi. You can use the lego chain and all the other parts from Zedpi's design (https://www.thingiverse.com/thing:1000713). So it is only slightly larger as the original one from Zedpi. The idea...

Not much about for 1:76 scale cars and for my newest project I wanted to FPV convert them for onboard racing which you can see on the project page here:...

Track curbs/island for Turbo Racing 1/76. ... Printed in white TPU and used red marker as seen in https://youtu.be/HteehgX9j2w

Track barrier for Turbo Racing 1/76. ... Printed in white TPU and used red marker as seen in https://youtu.be/HteehgX9j2w

I made new track wheels without sprockets, and now the track glides through the non-drive wheel smoothly, reducing a lot of noise. Here's an explanation video: https://www.youtube.com/watch?v=fhIfQ4ygYAI Also, the track is able to extend its full...

I designed new track wheels without sprockets, allowing the track to glide through the non-drive wheel smoothly and reducing noise significantly. To demonstrate this modification, I created an explanatory video here:...

This jib track with traveler and block needs 5 ball bearings. Outside dia 6mm inner dia 3mm and 2mm wide. Prints in PLA I hope you enjoy it. ... //Lars

I'm redesigning Staind RC Tank with a separate drive wheel and gear system. I plan to 3D print the gear in Taulman 910 Nylon for durability and the wheel in PETG for flexibility. The remix is based on Oger's enhanced drive wheel design. ...To assemble...

See the third design - a turret tank - here: https://www.thingiverse.com/thing:3481012 To build you'll need: -Four Lego tracks (Lego Part: x939 or 43903 - www.bricklink.com for best prices) -Four servos (continuous [FS90R] or modify a regular one –...

To print the entire set, you'll need to print the following parts: * 2 left bases (30cm or 50cm) * 2 right bases (30cm or 50cm) * The legs depend on how high off the track surface you want the cross beam to be - eight legs will bring it close to the...

So my metal track for the Leopard 2A6 keeps breaking after a year, probably because I played it in water and it became brittle now. There are two files: one original without extra support - you need to print this with support so that the two outer...

So my METAL track for the Leopard 2A6 keeps breaking after just a year. I suspect it's because I've been playing it in water and it's become so brittle now. There are two files available: 1. Original without extra support - You'll need to print...

Specifications: - Diameter: 51.5 millimeters (perfect fit for MST CSR tires, just like the original rims) - Height: 26 millimeters - Offset: 6 millimeters - Mount type: 12-millimeter hex bolt Print time: 2 hours and 20 minutes to produce one rim.

Tire out Diameter: 62mm Tire Width: 26mm Wheel Diameter: 45mm Drive Hex: 12mm

for more informations please watch the video https://youtu.be/4Bh49lGTMEA If you want to support my channal https://paypal.me/OM3DP