rc drift frame 3d models

The Mech Cover to Grip attachment and Magwell to Grip Frame attachment points have been redesigned to accept M3x25 screws and an M3 hex nut to further drop hardware requirements. This cumulatively drops the part count by 3 and the screw count by 8. I...

Happy 3d printing :) EN: My first home made printer. More or less, I originally planned to assemble the printer from the parts that remained at home after the upgrade of my Ender 3 printer. I used the electronics from Ender 3, motherboard 1.1.4 I...

A special feature is that you do not have to draw frame by  frame, but can also adjust the display duration of the individual  images.The template page shows the prefabricated special  fields, which we could finish at the end. First,...

Due to the fact that this model was first released on Gambody in 2016 as a one-piece Armor with a solid Station platform, for all the Fallout fans to print the cleanest power frame possible T-60 was cut into many assembly parts and adapted for...

It is a pretty archaic machine, so enough to tinker and update :)You can create a simpler handcrancked version with the parts to begin with.Is this machine too simple for you, take a look at the machine+ created by Warpster. Frame:I made the frame of...

(This was done due to Fusion 360 repeatedly failing to properly combine the parts to allow them to be exported as an STL for printing.) Materials NeededWhat you need: Printed one of the three provided files (RECOMENDED reinforced_holes.stl Pictured:...

The 3D printing model’s chosen scales are 1:16 for the FFF/FDM version and 1:32 for the DLP/SLA version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 80 parts;- A printed model stands 151 mm tall, 256 mm wide, 420 mm deep;- Two...

The 3D printing model’s chosen scales are 1:34 for the FFF/FDM version and 1:68 for the DLP/SLA version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 41 parts;- A printed model stands 505 mm tall, 332 mm wide, 186 mm deep;- Two...

The 3D printing model’s chosen scale is 1:34 for the FFF/FDM version and 1:68 for the DLP/SLA version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 61 parts;- A printed model stands 249 mm tall, 264 mm wide, 229 mm deep;- There are...

I printed it with supports only on the outside ramps that connect the LCD to the Prusa Frame, and the two-bottom touchscreen supports where there are floating squares to keep them straight. They do print ok without supports but not as clean. Like...

 The frame mounted supports are tweaked for reasonable clearance to the print head, the cross bar between the spool supports gives better clearance to the MMU3 to MK4 Print Head feed tube and better guidance for a tall print, The center roller...

The two squares rotated horizontally on the top and at the bottom with an axis in bearings mounted in the wall/frame. Later others came up with a similar system, where the two squares were divided into 3 pieces. The first video of this appeared in...

You can also mount it to the frame using the holes provided in the base. It is even possible to mount mount this tool directly on to your printers print head, if your printers design makes that an option.</p> <p>The only thing you need to ensure is...

Kit 4 of Millennium Falcon tracery, docking ring and décor elements is available for all the fans of the video game franchise and eager to have the spaceship’s 3D model upgraded with additional exterior elements.The tracery, that lines the ship...

So I designed my own.InspirationThe FilterHolder was inspired by the model from @DonDuce and his Case Fan 120mm for the Prusa Enclosure with Seals, HEPA & Carbon Filters .I decided to create my own model because his has an extra flange that would...

Long Necklaces add drama and sophistication with extended chains that frame the neckline. Y Necklace creates stunning visual interest by positioning charms or accessories against the Y-shaped framework. #BANGLES AND BRACELETS offers diverse...

I'm sure someone can come up with a better design but I couldn't find a way personally to more securely hold the endoscope camera without making the other wires stick out too far and bump into the frame when homing.There are a few requirements to use...

 The front frame is the part that the display actually sits inside.  The orientation will be clear if you look for the HDMI and USB ports.Next, the screen case bracket clips over the rear case panel.  Then the rear panel pops onto the front panel,...

You will be tempted to over tighten the bolts, don't or the wood will pull the square bolts in to tight and you will damage your frame. Check out these vertical rod supports. http://www.thingiverse.com/thing:35013 I think they are better and look...

3-Assemble the acetate sheet with the 3D printing frame, make a small hole with a scalpel to the acetate in the blocks that are going to hold it, this for greater security that it does not move at any time. 4 - Enter and adjust the rubber or spring...

6-29-2020 Another Add-On Platform Stand https://www.thingiverse.com/thing:4510900 UPDATE: 6-23-2020 Added: these parts for those with smaller printer (separated the controller from the base, to be mounted with M3 bolts)...

This is a complete frame replacement for that kit. The motor, control panel components, threaded rods and nuts, control board, and magnet are all reused. Additional components needed are as follows: A 5.5mm x 2.1mm DC Power Extension Cable (Right...

The above 2020 extrusions should be supported by brackets ensuring they are perfectly square with the frame. Bolt the 500mm linear to each of the 2020 extrusions. I would advise to put the rail so it bolts into the horizontal extrusion forming...

The lens was not intended to cover a full frame sensor, but it kinda-sorta does albeit with some significant but correctable light falloff! With the square baffle screwed in to the rear of the lens assembly (also harvested from the camera), there is...

There is also a "catch" key on the back foot that is intended to work alongside the bottom inside mount hole to mount and position the case on a 20mm extrusion frame. The front mount hole can be used with a T-nut and the back catch will fit into the...

Long term, I would recommend adding the inner frame (2 helical assemblies) and the guard, to avoid injuries. If you want to get fancy when 3D printing the guard: print it in two colours by swapping out the filament, and print the flat ring in...

The second goal of this build was to keep the possibility of converting back the coreYX to&nbsp;Ender 3 V2 and here we are.The benefits of CoreXY system is that your ender 3 v2 doesn’t have to move the heavy glass plate anymore, so by addressing this...

To install the Y-axis sensor on the aluminum profile of the machine frame under the platform, standard mounts for t-slots (M4) are used as those that come with the cnc machine. For the X, Z axis, print both pieces and attach them as shown above. For...

Just a thought you might just be able to pick the prime line off the bed before it prints the panel. Please add a wire from the ground terminal to the printer frame for safety. Any 120mm fan grill should fit just fine over the fan if you want the fan...

A nasal/columellar prosthesis device as claimed in claim 1 wherein said columella rod includes an additional extension for the purpose of manual manipulation of the frame for perfect adjustment in elevation and curvature, and can be cut for more...