rc car 1st gear 3d models

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/bJJFG1Etba0

1st differential gear RC-car

Double gear for RC car 39:12

this is a gear I have made for my rc car

Gear for RC gasoline car. SPECIFICATIONS: Outer diameter 43mm. Hole diameter 5mm. Total part thickness 6'8mm. Tooth thickness 5'8mm. Number of teeth, 41 teeth. ... Module 1.

Conic gear for rc car

Replacement bevel gear for my grandson's RC car. Obviously not as strong as injection molded nylon. But it did get the car back working. ... Rotate 180 degrees to print and no supports are required.

A Part for a RC Car of my Friend. ...

A gear shift lever to add detail to the interior of your RC or scale model.

http://www.thingiverse.com/apps/customizer/run?thing_id=1375790 Instructions Using the following options: 21_number_of_teeth = 1 05_gear_thickness = 3 00_build_plate = 3 26_rim_thickness = 18.5 22_backlash = .5 25_gear_thickness = 16 04_clearance = 1...

Gear for RC car/truck.

Gear to drive the differential gear in a Reely 1:14 RC car. The gear at the rear is also connected to the motor. Must be printed in PETG or ABS at maximum quality. ...No support structure needed.

Main Gear for 1/10 RC car (Carbon Fighter) Will not last long if printed in PLA - use Nylon for best durability

Replacement spur gear for RC toy car. made for small mabuchi like motor you may want to try to scale it up to match you needs : between 102 & 108 % center hole needs a little drilling for final fit. ...

spur gear for my old nitro rc car , they did not have spares on internet so i printed myself, got questions ask them !! ... centre hole = 11mm square hole = 15x15 mm and 1 mm thick theeth = 50

... with the teeth but some problems with the hexagon, too much backlash, so here is new version with better sizes. ... 47 teeth gear for rc nitro car, created from FS racing original gear on a 1:10 car, still not tested but assembled successfully...

Looking for the Gear / Axle for a Tumblebee RC Car? Took me several attempts to get it right, and I also added a ring under the gear to help with the clean removal of the supports. I'd recommend an infill of at least 60% to make sure the gear shaft...

I copied the original shattered gear which applies the drive to the back wheels of my son's Toy Story RC car. A couple of attempts later to get the bore size correct and came up with this which fitted and works spot on. ...

... by nitro, providing an authentic driving experience. With its detailed design and impressive performance, it's sure to deliver thrills for RC enthusiasts of all levels. Get ready for an adrenaline-pumping ride with this 1:8 scale RC Nitro car!

This is the 1st gear from a rotax DD2 2stroke engine. I have modeled this for my graded unit and i'm gonna do a simulation on it to calculate stress distribution. My graded unit is a failure analysis on this gear. I modeled this gear with a caliper...

This is the 1st gear from a rotax DD2 2stroke engine. I have modeled this for my graded unit and i'm gonna do a simulation on it to calculate stress distribution. My graded unit is a failure analysis on this gear. I modeled this gear with a caliper...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/bZ0QMnaRfUg

http://www.thingiverse.com/apps/customizer/run?thing_id=175150 Instructions Using the following options: fontsize = 8 plate_thickness = 3 font = write/orbitron.dxf line_spacing = 2 slitlength = 12 corner_radius = 3 line_9 = line_8 = line_7 = line_6 =...

My debut conceptual car model, yet to be named, was designed using SolidWorks 2013 software in just 1.5 days. KeyShot 4.0 Luxion Pro took an average of 45 minutes per rendering. ...I found the designing process more enjoyable than the rendering phase,...

Customized version of http://www.thingiverse.com/thing:268787 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=268787

Customized version of http://www.thingiverse.com/thing:268787 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=268787

Customized version of https://www.thingiverse.com/thing:53451 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=53451

Customized version of http://www.thingiverse.com/thing:268787 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=268787

Hi guys Just a rc car gear i designed for a friend thought id post it up incase anyone else would like to give it a print

Rc car Pinion gear that is for a 4mm motor shaft its about 48p 24t printed it at .12mm and .1mm