rc buggy 1 10 3d models

https://www.youtube.com/embed/I6AG4EhLrJI https://www.youtube.com/embed/THxFC0v_gK0 You can find all the non-printing parts needed for this project on the following list: | Name | Pieces | Link | | ------------- |:-------------:| -----:| |1. 6882RS|...

Human Height: 2 feet 0 inches Infill Percentage: 1%

Introduction This is an accurately scaled 1:10 MB jeep, which uses affordable drivetrain parts from a 1:18 scale Kulak crawler. The tires are not to scale, but they would be perfect if they weren't too pricey for me. Video Watch this video on...

I designed this specifically for my Thunder Tiger Atlantic Motor Yacht, an electric rc boat that requires precision and finesse, but I'm confident you can adapt it to fit any similar-sized vessel (ranging from 25" to 35"). Here's a video showcasing...

Humans typically require approximately 0.2 layers of height to achieve a substantial level of comfort. ...Moreover, they need around 10 percent infill density to maintain structural integrity and support their body weight effectively.

Massiver 3d gedruckter reifen plus Felge, Reifen wurde gedruckt aus TPU und die Felge aus PLA plus. ...Um dem ganzen mehr Stabilität yu geben wird dies verschraubt mit 6 x  M3 x 10 und 12 x M3 x 16 Schrauben

Connecting pieces to be used with 1/2 x 1/2 inch and 3/8 x 1/2 aluminum c-channel from Home Depot.  Can be made any size you need by cutting different lengths of aluminum.

I'm thrilled to report that no adhesive is required, it's a seamless fit! ... Print: 1 x Original 1 x Deluxe 2 x Adjustable

WHEEL ARM TRAILERS Representation of a wheel arm model of most 1/1 off road trailers Compatible with Fred'Trailers 1 axle models Do the symmetry under cura to have the arm on the opposite side of the trailer Fixing with 2 M3x6mm screws and 1 M2x6mm...

To assemble, you will need: - 20x20mm square dowel (measure the space between the wheels, multiply by two and then add 200mm to that to get the desired length of dowel) - Eight 20mm long screws (four millimeters wide) - Wall mounting screws and...

Still allows the cab light bucket to be fitted) Bumper: Blank number plate (hides the 2x bumper mount screws and gives a clean look) Logo number plate (ahead RC’s logo on the front. Hides bumper mount screws) Custom number plate Bumper mount (there...

Utilizes bearings with a diameter of 10 millimeters and a width of 4 millimeters, designed to scale at 1:10.

Original Jeep Cherokee Chief Comanche rims are available in a 1.9 inch size with a 12mm hexagon bolt pattern.

It took 10 hours to print this out. I made it for this truggy thing - https://www.thingiverse.com/thing:42198, but in the process, I ended up mixing it with this other one - https://www.thingiverse.com/thing:3055607. ...You can see what happened on...

... 2 variants, one is dished. Requires 10 x M2x5 bolts per rim to assemble. Designed to fit a standard 26mm tyre. +3mm offset, 12mm hex. Will take up to a 4mm shaft. Includes versions for FDM and resin. For personal use only. ...No commercial sales.

I'm replacing the light fixtures on my Everest 10 with top light bars, headlight cups, and taillight holders. I salvaged LEDs from a discarded Harbor Freight flashlight, which cost nothing since it was free -...

Thank you, domi1974, for creating the Suzuki Jimny Sierra 2018/2019 Body/Karosserie 1/8.2. ...I'd also like to contribute a set of spare tires!

Layer Thickness: 0.1 Millimeters Print Density: 25 Percent To complete this project, two large offset front rims and two middle offset rear rims require printing.

Hier mal ein Beispiel:...

These covers are designed specifically for 1.9 beadlock wheels, like those found at...

I'm still working on this project, feel free to use it as is or modify it to fit your needs - I designed it with the Axial SCX 10 Skid Plate in mind, but you can easily adapt it by making a mid-cut to get it to fit. My goal is to keep developing and...

After searching countless hours for a set of mud crush locks without success, I decided to design my own. ...these will fit all crawlers with 12mm hex. for 1.9 tires,

A compact measuring device takes precise readings on how much clearance exists between a vehicle's undercarriage and the terrain. ...Various models are available, ranging from 0.39 to 1 inch and 0.55 to 0.94 inches.

This is an assortment of accessories designed specifically for miniature remote-controlled vehicles, engineered to precision for optimal performance at a reduced scale of 1/10th the actual size.

... ...Files contain 12x5x7 spacers, inner and outer hubs, inner and outer hub shells, and hub covers that fit 1.9-inch/108mm tires (38mm wide). Installation: Insert the inner and outer hubs into the tire first; then install the inner and outer spacers.

Specifications: - Diameter: 51.5mm (precisely designed for the MST CSR tires; they fit seamlessly on original rims) - Height: 26mm - Offset: 8mm - Mount: 12mm hex Wall Line Count: 3 Layer Height: 0.3mm Infill Percentage: 20% Nozzle Size: 0.4mm...

Here are some ideas behind the design: * Easy prints that fly off the printer * No assembly required, zero nuts, bolts or screwdrivers needed, and maybe no glue at all, so I added some rib joints to the wheel-tyre * An airless tyre just for kicks,...

An old style gas-station in 1/10scale you can put some SMD LED´s in the Front plate and in the sign if you want it. The box in the stand have enough space for CR2032 cells an slots for wires unter the Stand.you can chose between with or without Sign...

... me. Because it's not the same, i decided to create at the same time a part that can be used as a glass, if you use a chrome paint for example. - even printed at 0.1 the details are not really good - don't hesitate to increase infill at 35-40%

I recommend printing it at a layer scale of 1.12 and using 100% infill for optimal results. For the best front view, I suggest trying to print it face-up with supports in place. Feel free to experiment with different settings to find what works...