rc alignment tool 3d models

Customized version of https://www.thingiverse.com/thing:37482 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=37482

For the Ford Ranger, the Mazda pickup trucks - B2300, B3000, and B4000 models - are also suitable options.

Print a boundary to place the included paper tape sticker correctly in the middle of the print area. Then place more pieces around to fill the whole area without any annoying seams thru the center. The boundary also give a nice indication of bed...

I printed these out to have two same height items to support the X carriage on the Sidewinder X1 while I was made adjustments. These were designed for the V3, the V4 has the ribbon cable connector where this was designed to go. May still be able to...

This is a pair of "legs" that will hold the x-gantry perfectly level while you adjust it. This video from Alex Kenis will show how it can be used instead of the CD cases he uses. ... https://www.youtube.com/watch?v=AN0MlQMMew0&t=149s You don't need it,...

Customized version of https://www.thingiverse.com/thing:49911 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=49911

Customized version of https://www.thingiverse.com/thing:695599 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=695599

Customized version of https://www.thingiverse.com/thing:2424931 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2424931

This is a redesign of the ball marker by Chuck Hellebuyck Elproducts Print Settings Printer: Wanhao i3 Rafts: No Supports: No Resolution: .15 Infill: 25% Category: Sport & Outdoors

Print SettingsRafts: NoSupports: NoResolution: 0.15Infill: 35%Filament material: PLA+

This is a redesign of the ball marker by Chuck Hellebuyck Elproducts. The previous design didn't print well, but it functions perfectly fine. If anyone tries printing with a different orientation, please leave a comment sharing your results. The flat...

<p>I printed these out to have two same height items to support the X carriage on the Sidewinder X1 while I was made adjustments.</p> <p>These were designed for the V3, the V4 has the ribbon cable connector where this was designed to go. ...May still be...

Using the following options: Tube diameter is set to 34. Jig height has been adjusted to 20. Four fins will be implemented with a width of 3.1 units. The parameter $fn, responsible for rendering precision, is fixed at 150. The jig fin width will...

<p>This is a redesign of the ball marker by Chuck Hellebuyck <a href="/Elproducts/about">Elproducts</a></p> <p>This one didn't print great, but it works good. If anyone tries a different print orientation please leave a comment with your results.

This is a redesign of the ball marker by Chuck Hellebuyck Elproducts (http://www.thingiverse.com/Elproducts/about)

This is a total overhaul of the ball marker by Chuck Hellebuyck Elproducts. ...Print Settings Printer: Wanhao i3 Rafts: Not Required Supports: None Needed Resolution: High, .15mm Infill: Moderate, 25% Density

Customized version of https://www.thingiverse.com/thing:37482 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=37482

I printed these out to have two identical items to support the X carriage on my Sidewinder X1 while making adjustments. These were created for the V3, but the V4 has a ribbon cable connector where this was intended to fit. ...They may still be usable...

Customized version of https://www.thingiverse.com/thing:695599 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=695599

This is a redesign of the ball marker by Chuck Hellebuyck Elproducts (http://www.thingiverse.com/Elproducts/about) This one didn't print great, but it works good. If anyone tries a different print orientation please leave a comment with your...

Customized version of http://www.thingiverse.com/thing:695599 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=695599 V1 didn't fit on the print bed of my RepRapPro Fisher so I shortened the fin support height. ...I will...

This is a pair of "legs" that will hold the x-gantry perfectly level while you adjust it. This video from Alex Kenis will show how it can be used instead of the CD cases he uses. You don't need it, but I used the knob, an m3 bolt and t-slot nut to...

For locating the CBORE location for 1.5" T-slotted framing. ...Reference McMaster 47065T102 or equiv.

Same design as RooMar but I added some height because my head was touching the plate

Customized version of https://www.thingiverse.com/thing:37482 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=37482

I'm a Customized Version of Thingiverse's Project 695599 Designed with the Customizer App from Thingiverse! ... ** Untested, Will Provide Updates on Fit After Printing ** ** Step-by-Step Instructions for Use: ** Selecting Options: • Tube Diameter:...

A device specifically designed to position a 2020 extrusion used in the Y-axis of an Anet AM8 accurately and consistently.