rc 1 28 3d models

Like… very-nearly-the-whole-MK3s-build-plate-big, so don't be surprisedSettings (how I printed mine, at least):Prusa Slate Silver PETG0.4mm nozzle.2 layer height20% infill (resulted in some surface scarring, but it's not visible on mine when in...

For more information on how to create a customized bearing peg scroll to the bottom of Print Instructions. Single mount hole: 'I' design elegant but tricky to mount 'L' design is easy to mount Two mount holes: 'Slim' design, minimal side...

It is probably best to use a new or very sharp, narrow craft knife/ scalpel to remove the brim around the edge and under a decent (x3 or better) magnifier, with a piece of thick grey or white (for contrast) cardboard or hardboard (NOT metal, for the...

If you print different material just change a positive or negative Z offset in the slicer for each material.How to useStep 1: Print the carriage and belt peg.Step 2: Remove the Hercules carriage and install this bed leveling carriage. Copy the bed...

This was an easy fix as all we had to do was lower the bottom anchor point of the mouth by 0.1 cm and it brought the rest of the mouth down with it due to the feature being fully defined. This was a functional change because the mouth is the part of...

(I haven't tested it.)I decided to use a 12V 1 Amp mains adapter and a small D-SUN fixed 5V voltageregulator module fitted inside the camera housing.These modules are available from eBay (search for "MP1584EN")NOTE There are versions of this D-SUN...

Also be sure to not accidentally create any automatic relations unless explicitly mentioned to do so.Draw constraint box   Center rectangle on the origin, with construction lines that go through the midpoints of the rectangle30mm x 65mmSet the top...

For everybody else, below are the recommended assembly steps: 1. Test-mount mosquito with just the Rear E3D Mount block and two screws. This is to approximate the length of bowden tube. Do a rough size estimation, remove hot end, insert the cut...

####Instructions for use of this Mutant Interface plate: 1. Un-screw and remove the metal or plastic cover from the Hotend assembly. 2. Un-screw the fan(s) from the cover and/or hot-end assembly. 3. Un-screw the bolts that hold the hot-end to the...

You will reuse pieces of this, so do not discard. Attach 1 section of the 15 x 20mm cable chain to the "Openrails_Z_frame_Cable_Chain_End_3_0_a.stl" part using two of the M3 screws, and secure that to the frame next to the control box with the T slot...

* This will pause the print at layer 2 and 5; layer 3 and 6 if you count from 1, but the slicer counts from layer 0. When printing, during the first pause switch to white from black, then switch back to black for the second pause. Ensure that you...

The geometry provides the necessary stability.You can extend and setup the HIVE as you wish because of its modular design!Here are a few use cases (See pictures):Kitchen-HIVEMoney-HIVEBeer-HIVEInsects-HIVEWeek-HIVE… if you have another one, feel...

Assembly is straightforward:1. Get all the characters required for your label text, a tag of your choice and a tray:2. Slide the plates into the tray. Make sure the plates can not fall out of the tray, by holding the tray like so:3. Fill up the...

The benefit of this version is you don't have to disassemble the extruder to change out non Q-link stepper motors.Cable RetainerNo Cable Retainer Notes1. The BEM Idler is wider than the original Bear Idler by 4mm due to needing to add 4mm to the...

Some tips I've figured out:1) Print the "stream" part with low infill (10% or even 5%) to minimize the weight of the thick off-center part that is inside the "cup". Be careful removing this part from the bed, since with low infill it won't be as...

Part 1 and 2 are the normal Body front, part 3 and 4 form the Body middle, part 5 and 6 the Body back. You Need to print eiher the 3 parts or the 6 parts of the Body. The later ones have no positioning Elements to glue them together, you are on yor...

ender 3 tried and true design fixes based on science / common sense FOR ANY OF THIS TO WORK https://www.youtube.com/watch?v=4bFYH0X3qjk this is the number 1 alignment and assembly of everything is 90 percent of print quality last 10 will be slicer /...

Take the eye measurements 0.5cm from the sides, and 1.1cm from the top of the second triangle. ...Set the eye dimensions to 0.6cm to put them in the proper place.</p><p><img...

______________ Update 1: Added versions of the Engine covers with filled grates for better overhangs. Old version kept as well. Look for "w Fill". Update 2: Added another version of the engine covers, with struts positioned behind the gaps...

I suggest you use the following order to build the printer, so you can start while parts are still printing. General Parts: 1x SKR Pro V1.1 5x TMC2209 stepper drivers 1x LCD display 12864 (may be replaced by a touch screen) 2x 10 pin 1.3m ribbon...

Fits all Bambu spools and Extrudr 1kg and 1.1kg spools.Original Bambu Clamp & Spindle - Fits most Bambu spools with the exception of a lot of newer ones. This is a better option for spools it fits, as there will be less play in the assembly.Generic...

Video recording is also possible.The field of view at the focal plane is 18x12mm on a full-frame camera, or 12x8mm on a 1.5x crop camera. Larger subjects can't be photographed, as the magnification is fixed at 2x.Two Sony E/FE cameras are required,...

Even if you drop only 1-2 volts it usually results in a significant drop in max static pressure - the relation probably isn't linear. This is how the "Low Noise Adapter" (L.N.A.) cable of a Noctua fan works. It connects a resistor in series with the...

Make sure the right side mount is in the correct orientation.Trim the shorter wire so there is 2-5cm (1-2") sticking out both ends of the right side mount.Strip the ends of the shorter wire and solder to the end of the rear LED strip, red to + and...

Sorry for the print quality, I haven't yet calibrated the filament I printed it with (I just wanted to get it printed and running, didn't care if it looked all that good). Vitamins: lots of M3 x 8-14 mm screws 3, M3 x 20 mm screws 2-4, M4 x 30-40 mm...

A bolt length of 30mm is as short as I would go, but longer will work just as well, if not better.&nbsp;Work the SuperPINDA Precision Adjuster onto and off of the SuperPINDA probe (or stand-in M8-1.0 bolt) several times to “break in” the part. In...

Most of the fonts listed in the drop-down selection for this thing can be downloaded from: [Google Fonts repository](https://fonts.google.com/) To make a font available to OpenSCAD you have two options: 1) Install the font to the system. 2) Add the...

Commodore PET Replacement Keyboards (under construction) 1) "SK" Keyboard Shell 3D Models 2) "SK" or Business Keyboard 3) "GFX" or Standard Keyboard The Commodore PET is a part of computing history, one of the "trinity" of home computers from 1977......

The 4010 mount is hard to see as the fan model I used has slightly thicker mounting ears than the fan I received from TRONXY so they merge together visually. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: Yes Resolution: Adaptive;...

In the ordinary way this would be a hindrance but here we take advantage of the backlash to create a stomping gait.AlternativeIf you have difficulty with these instructions an alternative is available on:...