razor blade model

It does not need power to work, it is simply a switch that opens when the sensor tip touches a surface. It is probably NOT suitable for a 3D printer bed leveling system because it could touch the model you are printing. If you added a removable cap...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

The design uses 12 '10mm x 3mm' (the magnets are actually closer to 9.95mm x 2.67mm).This is a spin-off from my earlier light-pull magnetic door catch: https://www.printables.com/model/209370-magnetic-low-profile-floating-head-quiet-door-catc , but...

Able to hold 1 stack of cards and 2 columns of hexes. --4-2-17-- Added player card 2.2, a little bit smaller on the separator pieces that come off the model, should be easier to fit in the box. --4-2-17-- Removed older hex and cards .stls and...

IntroductionThis model provides an effective, low-cost teleprompter for livestreaming and recording. Using a Raspberry Pi and Pi Camera (the cheap, non-HQ one provides great full-HD video in this application), your phone to display your script or...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

 The switch is wired so it goes from Off to On with no sounds to On with sounds. ...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Mounting: The EPL-LED-150W-RT...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 20 stencil_pattern_element_shape = 3...

Also, I am considering some re-design of the right motor plate that currently interferes with the model fan duct. That would recover a bed Y-dimension back to 220. So, after all the print area will be 210x220mm... Parts to print: all parts at last...

The bracket that goes around the metal fan cover is specific to the Ender 5 Plus (also used on CR-10, CR-10S, and many of the other Enders) but does not fit all variations (V2, V3, CR-10S Pro models does not fit.) A list of the printers I think this...

However, they are split down the middle so they can fit through the holes with a firm hand, before springing back to the larger size. So thank you for the reviewer who made me take a closer look at at my model.I am always open to others ideas or...

Extending the print head cable on this model is not unheard of, it is a common change made when upgrading this printer to a direct extruder. The portal cable (black) does not need to be extended, even for the extension kit for 50mm, as long as you...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

If the diameter of mounting holes is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit (the only thing that cannot easily be scaled is the small enclosure for the BT-amplifier). ...

License ------- The "Arduino Nano NeoPixel Ring Base" models (.stl) are licensed under the [CC BY](https://creativecommons.org/licenses/by/4.0/) license by [Code and Make](https://codeandmake.com/). The "Arduino Nano NeoPixel Ring Base" code...

If they are different, please update the Fusion 360 model and re-generate the toolpaths. Also, if you plan on using different tools for the above operations, make sure you update the tools (and associated feeds and speeds) and regenerate the tool...

The models in these STL files are scaled for a 58cm head circumference. (Refer to photo of T800 for how to measure the size you will need to print) Just scale in your slicer software on XY by 1/58*[your figure]. Do subscribe to my YouTube...

As always, the .blend file and pre-supported .obj (the one that I used to print it on my Prusa mk3 with a .25 mm nozzle) for this model are available to my patrons at https://patreon.com/VirtuallyJason. If you appreciate my work and have a few...

If using liquid electrical tape, allow it to cure before continuing. Gluing Use a small amount of hot glue to attach the diffuser to the LED mount. Using To use, simply attach a 9v battery and insert the LED mount into the base, ensuring that the...

... and the stuff that I put in that spot. As always, the .blend file for this model is available to my patrons at https://patreon.com/VirtuallyJason. ...If you appreciate my work and have a few dollars to spare each month, please consider joining!

Generate and print your own, compatible with any existing threads!This model was designed in Fusion 360 and uses 3 required input parameters and standard Metric thread profile equations to generate a cap that will perfectly fit any of your threaded...

 February 17th, 2022Parts Revised:Wire GuideThere was an error in the model that I didn't catch.  Part of the base wasn't extruded in Fusion360.  Version 1.3 is still usable, but it's not what I had intended, so here is version 1.4 of...

My model was FDM printed only. Actual code will be available here: https://github.com/Kandzior/NeverHotTeaAgain Charging is done by plugging micro-usb cable to the charger module through hole at the side. When you disconnect the plug, you can cover...

If desired you can secure it in place with a sticky pad or some hot glue. Push the insert into place. Lower the NeoPixel Ring into place, ensuring to route the wires through the slots in insert. If you are using a diffuser, place it on top of the...

... weapon. By Alex Wellerstein, a historian of science and an assistant professor at the Stevens Institute of Technology, in New Jersey. Attributions: •Screwdriver by user DAPE, Cults3D (under CC-By-Sa-Nc). •Demon Core modeled by Szadros. ...

Unbeatable speed and rigidity for such a small package. External links: Buy Kit at Rat Rig Step by step Build Manual Facebook Rat Rig 3D Printer Community Project Page (BOM, Build Guide, Files, Electronics, Firmware) CAD 3D Model Features ...

Depending on your printer tolerances, it may be more or less tight, but if everything lines up it should be no problem.Fasten the 3 screws at the "top" (in this orientation) once the spine is flush with the caseCHANGELOG2022-03-01 - Moved away from...